Manuels d'utilisation pour Apollo ESP6000

Table des matières

• 1. Getting started

  10
• 1.1 Safety Precautions

  10
• 1.2 Packing List

  10
• 1.3 Document Amendment History

  11
• 1.4 Manual Objectives

  12
• 1.5 System Specifications

  13
• 1.6 Architecture Overview

  15
• Block Diagram

  15
• VIA TwisterT VT8606 (ProSavage PN133T Chipset)

  16
• VIA VT82C686B South Bridge

  17
• VIA VT1612A

  19
• IDE Interface (Bus Master Capability and Synchronous DMA Mode )

  20
• USB

  20
• Ethernet

  20
• Winbond W83977EF

  21
• Compact Flash Interface

  22
• 2. Hardware Configuration

  23
• 2.1 Product Overview

  24
• 2.2 Jumper and Connector List

  25
• 2.3 Setting Jumpers & Connectors

  27
• AT/ATX Power Select (ATATX1)

  27
• COM2 – RS-232/422/485 Select (J3, J5)

  27
• Clear CMOS (J4)

  28
• COM1 – Ring, +12V, +5V Select (J6)

  28
• Serial Port 3 / Port 4 Connector in RS-232 Mode (CM1, CM3)

  29
• Serial Port 1 Connector in RS-232 Mode (CM2)

  29
• Serial Port 2 Connector in RS-232/422/485 Mode (CM4)

  31
• IDE Connector (CN1)

  34
• CPU Fan Connector (CN2)

  36
• CD-ROM Audio Input Connector (CN4)

  36
• Audio Connector (CN5)

  37
• Primary LCD Panel Connector (CN6)

  38
• Secondary LCD Panel Connector (CN8)

  39
• PC/104+ Connector (CN7)

  41
• PC/104+ Connector (CN10)

  42
• IrDA Connector (CN9)

  46
• LCD Inverter Connector (J1)

  47
• Auxiliary Power Connector (J2)

  48
• ATX Soft-power Connector (J9)

  48
• Parallel Port Connector (PNT1)

  49
• Primary Power Connector (PWR1)

  51
• Secondary Power Connector (PWR2)

  51
• USB Connector (USB1)

  52
• LCD Backlight Brightness Adjustment Connector (VR1)

  53
• STN LCD Contrast Adjustment Connector (VR2)

  53
• 3. BIOS Setup

  54
• 3.1 Starting Setup

  55
• 3.2 Using Setup

  56
• 3.3 Getting Help

  57
• 3.4 In Case of Problems

  57
• 3.5 Main Menu

  58
• Standard CMOS Features

  59
• Advanced BIOS Features

  62
• Advanced Chipset Features

  66
• Integrated Peripherals

  70
• Power Management Setup

  73
• PnP / PCI Configuration

  77
• PC Health Status

  78
• Frequency / Voltage Control

  79
• Load Fail-Safe Defaults

  80
• Load Optimized Defaults

  80
• Set Supervisor / User Password

  81
• Save & Exit Setup

  82
• Exit Without Save

  83
• 4. Drivers Installation

  84
• 4.1 Install Chipset Driver (For VIA VT82C686B)

  85
• 4.2 Install Display Driver (For VIA TwisterT VT8606)

  87
• 4.3 Install Audio Driver (For VIA VT1612A)

  88
• 4.4 Install Ethernet Driver (For Realtek RTL810x, RTL813x Family)

  89
• Measurement Drawing

  90
• Appendix A: BIOS Revisions

  92
• Appendix B: AWARD BIOS POST Messages

  93
• Overview

  94
• Post Beep

  94
• Error Messages

  94
• CMOS BATTERY HAS FAILED

  94
• CMOS CHECKSUM ERROR

  94
• DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER

  94
• DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP

  94
• DISPLAY SWITCH IS SET INCORRECTLY

  95
• DISPLAY TYPE HAS CHANGED SINCE LAST BOOT

  95
• EISA Configuration Checksum Error PLEASE RUN EISA CONFIGURATION UTILITY

  95
• EISA Configuration Is Not Complete PLEASE RUN EISA CONFIGURATION UTILITY

  95
• ERROR ENCOUNTERED INITIALIZING HARD DRIVE

  95
• ERROR INITIALIZING HARD DISK CONTROLLER

  95
• FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT

  95
• Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY

  96
• KEYBOARD ERROR OR NO KEYBOARD PRESENT

  96
• Memory parity Error at

  96
• MEMORY SIZE HAS CHANGED SINCE LAST BOOT

  96
• OFFENDING ADDRESS NOT FOUND

  96
• OFFENDING SEGMENT:

  96
• PRESS A KEY TO REBOOT

  97
• PRESS F1 TO DISABLE NMI, F2 TO REBOOT

  97
• Should Be Empty But EISA Board Found PLEASE RUN EISA CONFIGURATION UTILITY

  97
• Should Have EISA Board But Not Found PLEASE RUN EISA CONFIGURATION UTILITY

  97
• Slot Not Empty

  97
• Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY

  98
• FLOPPY DISK(S) fail (80) → Unable to reset floppy subsystem

  98
• FLOPPY DISK(S) fail (40) → Floppy Type dismatch

  98
• Hard Disk(s) fail (80) → HDD reset failed

  98
• Hard Disk(s) fail (40) → HDD controller diagnostics failed

  98
• Hard Disk(s) fail (20) → HDD initialization error

  98
• Hard Disk(s) fail (10) → Unable to recalibrate fixed disk

  98
• Hard Disk(s) fail (08) → Sector Verify failed

  98
• Keyboard is locked out - Unlock the key.

  98
• Keyboard error or no keyboard present.

  98
• Manufacturing POST loop

  98
• BIOS ROM checksum error - System halted.

  98
• Memory test fail.

  98
• POST Codes

  99