Manuel D’UtilisationTable des matièresTitle Page1Notice3Contents7Introduction111.1 About This Manual111.2 Getting Help121.3 Document Conventions131.4 Related Documentation141.5 Overview151.5.1 SmartSTACK 100 ELS10016TX Architecture16Port Trunking18Autonegotiation18Store and Forward Switching19Discarding Local Traffic19Spanning Tree Algorithm201.5.2 SmartSTACK 100 ELS10016TX Bridge Address Table211.5.3 SmartSTACK 100 ELS10016TX Port Mirroring221.5.4 SmartSTACK 100 ELS10016TX Sample Applications22SmartSTACK 100 ELS10016TX Trunking23Virtual Workgroups241.6 Local Console Manager271.6.1 Command Syntax Conventions281.6.2 Basic LCM Commands29Help29Erase31Exit or Logout31Traplog31Unpacking and Installing Your ELS100-16TX332.1 ELS100-16TX Front Panel332.2 Installing an EPIM362.3 Installing the ELS100-16TX38Rack-Mounting an ELS100-16TX382.4 Checking the Power-up Diagnostics Sequence402.5 Connecting the Local Console Manager402.6 Connecting to the Network412.6.1 Connecting UTP Cables422.6.2 Connecting a Segment to the EPIM-100FX43Fiber Optic Network Connection44Configuring Your ELS100-16TX473.1 Assigning IP Addresses483.1.1 Displaying IP Addresses503.1.2 Deleting an IP Address503.1.3 Changing a Subnet Mask503.2 Enabling Bridging513.3 Disabling Bridging523.4 Displaying Bridging Functions523.5 Enabling Trunking53Trunk Groups543.6 Disabling Trunking563.7 Displaying Trunking Status573.8 Enabling Port mirroring593.9 Disabling Mirroring593.10 Displaying mirroring Status603.11 Defining and Deleting Workgroups623.12 Assigning a Community Name643.13 Configuring Broadcast/Multicast Storm Protection653.14 Modifying MIB Variables663.15 System Contact663.16 System Name673.16.1 System Location673.16.2 Community Names67Set Community Name683.16.3 Aging Parameter68Monitoring and Managing Your ELS100-16TX694.1 ELS100-16TX Management Tools694.2 ELS100-16TX Statistics694.2.1 Gathering Statistics704.2.2 System Statistics704.2.3 Ethernet Port Statistics714.3 Using LCM to Check ELS100-16TX Status724.3.1 Displaying Status724.3.2 Displaying MAC Addresses744.3.3 Displaying Manufacturing Information764.4 Managing the ELS100-16TX774.5 Using LCM to Manage the ELS100-16TX774.5.1 Disabling a Port784.5.2 Enabling a Port78noRIP Option794.5.3 Changing a Subnet Mask794.5.4 Changing a Community Name804.5.5 Setting the Baud Rate814.5.6 Setting a Reboot Time82ELS100-16TX Diagnostics and Troubleshooting835.1 Power-up Diagnostics835.1.1 Power-up LED Sequence835.1.2 Specific Power-up Tests845.1.3 Software Checksum Comparison845.1.4 Power-up Diagnostics Results855.2 Responses to Failures at Power-up855.3 Status and Activity Indicators855.4 Troubleshooting885.5 ELS100-16TX Does Not Power Up885.5.1 Connectivity Problems895.5.2 ELS100-16TX Has Rebooted895.5.3 ELS100-16TX Does Not Respond to NMS89Technical Specifications91A.1 ELS100-16TX Specifications91Physical91Electrical91Connector Ports91Environmental91Diagnostic LEDs92Standard Support92Address Table Size93Management Support93Regulatory Compliance93A.2 Serial Cable Pin Assignments93A.3 100BASE-T Pin Assignments94A.4 Straight-through Wiring95A.5 Crossover Wiring95A.6 The 5 - 4 - 3 Rule96A.7 EPIM-100FX Specifications96Glossary99Taille: 730 koPages: 110Language: EnglishOuvrir le manuel
Guide D’Installation RapideTable des matièresTitle Page1Notice3Contents5Welcome to the SmartSTACK 100 ELS100-16TX7Getting Help7Setting Up and Powering Up the ELS100-16TX8Attaching Power Cord and Connecting to a Power Source8Checking the Power-up Diagnostics Sequence8Connecting UTP Cables10Installing an Ethernet Port Interface Module (EPIM)11Connecting a Multimode Segment to the EPIM-100FX12Fiber Optic Network Connection12Connecting the Local Console Manager to a Terminal13LCM Commands14Taille: 220 koPages: 16Language: EnglishOuvrir le manuel
