Manuel D’UtilisationTable des matièresPREFACE3Notes on this Manual3Registered Trademarks3Copyright3Contents5INTRODUCTION91.1 Checking the Accessories101.2 Parts Names and Functions11Front View11Rear View12Control Panel13SETTING UP THE CUTTER PLOTTER152.1 Connecting to Your Computer162.2 Turning on the Power172.3 Loading the Medium18Loading a Roll Medium18Loading Sheet Media22Aligning the Push Rollers232.4 Upon detection of no medium during roll media cutting252.5 Adjusting and Mounting the Cutter Pen25Types and Features of Cutter Blades26Cutter-Pen Construction26Replacing the Cutter Blade26Adjusting the Blade Length27Mounting a Cutter Pen28BASIC SETTINGS AND OPERATIONS313.1 Setting the Format of Data to be Received32Setting the Command Mode32Setting the STEP SIZE33Setting the ORIGIN POINT333.2 Setting the Interface Conditions343.3 Setting the Cutter-Pen Conditions35Selecting Cutter-Pen-Condition Setting Areas36Storing Cutter-Pen-Condition Setting Areas36Setting TOOL (cutter blade or pen)37Setting OFFSET37Setting FORCE38Setting SPEED38Setting QUALITY393.4 Displaying the Effective Cutting Area393.5 Moving the Pen393.6 Setting the Initial Cutting Position403.7 Stop Function413.8 Moving the Pen Carriage in +100 mm Steps423.9 Test Cutting42FUNCTION SETTINGS AND OPERATIONS454.1 PAUSE Menu List464.2 Reading the Auto Registration Marks474.3 Setting the FEED function484.4 Setting AUTO PRE-FEED494.5 Setting TANGENTIAL Mode504.6 Auto-Registration-Mark-Reading Settings52Registration-Mark Menu Tree54Setting the Registration-Mark Mode554.7 Clearing the Buffer Memory664.8 Aligning the Coordinate Axes674.9 Distance Adjustment694.10 Setting the PAGE LENGTH714.11 Setting the Cutting/Plotting Area724.12 Expanding the Cutting/Plotting Area734.13 Rotating the Coordinate Axes744.14 Mirroring754.15 Cutting/Plotting Using the Buffer Memory764.16 Sorting Settings784.17 Interface Settings794.18 Setting the Format of Data to be Received80Setting the Command Mode80Setting the STEP SIZE81Setting the ORIGIN POINT814.19 Blade Wear Detection82Checking the Wear Rate82Setting Wear-Rate Groups83Setting Wear-Rate Factors84Clearing the Total Distance (Wear Rate)844.20 Raising and Lowering the Pen864.21 TEST Mode87Condition-List Printing87Self-Test-Pattern Printing88Dump Mode88Cutting Demo89Cutting Force Test Cutting904.22 Setting the PEN UP SPEED924.23 Setting the OFFSET FORCE934.24 Setting the OFFSET ANGLE944.25 Setting the STEP PASS954.26 Setting the Initial Down Force964.27 Setting the LENGTH UNIT97Setting and Using the Special Functions995.1 Description of Special Functions A100Enabling/Disabling the “:” and “;” Commands (when the COMMAND setting is GP-GL)100Moving the Pen While Raised or Lowered in Response to the “W” Command (when the COMMAND setting is GP-GL)100Model ID Response (when the COMMAND setting is HP-GL)100SETTING PRIORITY100Blade-Tip Initial Position Setting100Enabling/Disabling PEN UP MOVE101Enabling/Disabling the Media Sensors101Enabling/Disabling the Home Sensors101Circle-Command Resolution Setting (when the COMMAND setting is HP-GL)101Enabling/Disabling Blade Wear Detection101Setting up the PAUSE KEY101Setting up the COPY MENU1015.2 Setting Special Functions A1025.3 Description of Special Functions B103Display Language Setting (MENU LANGUAGE SELECTION)1035.4 Setting Special Functions B103TROUBLESHOOTING1056.1 The Cutting Plotter Does Not Operate When Turned On1066.2 The Cutting Plotter Does Not Operate Correctly1066.3 The Cutting Results Are Unsatisfactory1076.4 An Error Message Was Displayed109Appendix113Appendix A Main Specifications114Appendix B Options and Supplies115Appendix C External Dimensions116Appendix D Menu Tree117INDEX119A119B119C119D119E119G119H119I119L119M119N120O120P120Q120R120S120T120U121W121Taille: 3,9 MoPages: 122Language: EnglishOuvrir le manuel