Manuel D’Utilisation
Table des matières
- When you install the system or change the system configuration, it is necessary to execute setup ...23
- Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid remov...23
- In the system environment setting, you use the BIOS setup (Setup Menu below) and the ISA configur...24
- Depending on the extended board, there are restrictions on setting for IRQ and ROM addresses. See...25
- If you use Windows NT, use “Auto Select” in the Setup Menu to set IRQ setting values for extended...25
- NOTE: Hitachi PC assumes no responsibility for failures resulting from the use of PCI or ISA boar...25
- The Setup Menu allows you to make basic settings for the system equipment. The settings are store...26
- You can use and keys to switch between menus (between Main and Advanced, between Advanced and Sec...26
- If the operating system has already started before the key is pressed, terminate the OS and then ...27
- Used to set each setting items. Move the cursor to each of the setting items marked , then press ...28
- 28
- 29
- 29
- 29
- 29
- 29
- 29
- 30
- 30
- Before exiting the Setup Menu, insert ISA Configuration Utility DISK1 into the floppy disk drive....30
- To move the cursor within the System Time or the System Date area, press key, or press key while ...31
- 31
- 31
- 31
- 31
- 31
- 31
- 31
- Hitachi products do not support IDE hard disks. Hitachi PC does not guarantee performance if an I...31
- NOTE: If the memory capacity displayed is less than the actual memory capacity, contact the maint...32
- NOTE: “Reset Configuration Data” and “Execute ROM Diagnostic” are used solely for maintenance pur...32
- The correspondence between PCI IRQ lines and PCI slots is as follows: Line 1 corresponds to slots...33
- 33
- NOTE: Make sure that the settings in Base I/O address/IRQ for serial port 1 do not overlap with t...33
- 34
- 34
- 34
- 34
- 34
- 34
- 34
- 34
- 34
- 34
- NOTE: Installation of a PCI board without parity capability might cause a parity error. If such a...35
- If you set a password in the Security menu, be sure to remember that password. Should you forget ...37
- Specify the priority of devices to boot/load. To change priority, move the cursor to the device, ...38
- NOTE: When PC98-compatible SCSI boards such as PC-CS7331 or PC-CS7231A are installed, more device...38
- Used to specify the order of booting for the hard disk. Check whether the display is the same as ...38
- • To continue processing without recording the data, either select “No” or press key to return to...39
- If you use values other than those recommended, evaluate such values sufficiently before use. Hit...40
- The Hitachi VisionBase 8880R Server system equipment does not support Plug and Play compatible op...40
- Some improper operation can make ICU floppy disks unusable. In such a case, create new backup dis...41
- Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid remov...41
- If two extended boards use the same resource, one of the two might not operate at all or the syst...42
- Choosing each menu (portion with characters) will display its menu list. By choosing an item on t...43
- Choosing each button (portion with characters) will display its dialog box. There are four button...43
- 43
- 43
- 43
- 43
- • You can also display Help for the command currently being executed. Choosing [Help] in the dial...43
- If you choose [Yes], system configuration data file “SYSTEM.IMG” is saved into DISK2 in drive A. ...44
- You can either display all resources used by the system equipment or resources used by extended b...45
- Resources currently in use by the system equipment are displayed in the [System Resource Usage] d...45
- The [Card Resource Usage] dialog box is displayed as shown below. In this dialog box, you can che...46
- To install an extended board, make ICU settings in the following steps. The following example use...46
- Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid remov...47
- Referring to the manual of the extended board, either choose or enter the appropriate values. If ...48
- This utility automatically reserves higher 6-bit addresses by reserving lower 10-bit I/O address ...48
- Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid remov...48
- Be sure to avoid changing the setting of the IDE controller, otherwise the programs may malfunction.48
- Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid remov...49
- Built-in devices must be added or exchanged by maintenance personnel only. Be sure to avoid remov...50
- The ICU program disk contains information about the boards that have been set. If this disk has b...50
- When you change ICU settings and exit the ICU, the newest configuration information is saved as t...51
- Before setting up the system equipment again, remove all boards other than those already installe...51
- 52
- • If the above message is displayed only within one extended board, only set the lowest-order value.53
- • In the [Memory] list box “1FFFFF” is always displayed; however, the actual memory capacity is c...53
- This section explains how to return the settings to defaults and what action to take when you can...54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 54
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 55
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 56
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 57
- 58
- 58
- 58
- 58
- 58
- To avoid a STOP error from occurring in Windows NT when configuring multiprocessors, it is strong...59
- • If your system has more than 3.5GB of memory, you must complete the following steps for a succe...59
