Manuels d'utilisation pour JAI AT-200GE

Table des matières

• JAI GigE VisionⓇ Camera operation manual

  6
• Introduction

  6
• Before using GigE Vision camera

  7
• Software installation

  8
• Camera Operation

  8
• 1. General

  8
• 2. Camera nomenclature

  8
• 3. Main Features

  9
• 4. Locations and Functions

  10
• 4.1. Locations and Functions

  10
• 4.2. Rear panel indicator

  11
• 5. Pin Assignment

  12
• 5.1. 12-pin Multi-connector (DC-IN/Trigg

  12
• 5.2. Digital Output Connector for Giga

  12
• 5.3. D-Sub 9pin connector (For GPIO)

  13
• 5.4. DIP switch

  13
• 5.4.1 SW-600

  13
• 5.4.2 SW-100

  14
• 6. Input and output circuits

  15
• 6.1. Iris video output

  15
• 6.2. Trigger input

  15
• 6.3. XEEN output

  15
• 6.4. Auto iris video output level

  16
• 7. GPIO (General purpose inputs and ou

  17
• 7.1. Overview

  17
• 7.1.1 LUT (Look Up Table)

  17
• 7.1.2 12-bit Counter

  18
• 7.1.3 Pulse Generators (0 to 1)

  18
• 7.2. Opto-isolated Inputs/Outputs

  18
• 7.2.1 Recommended External Input circu

  18
• 7.2.2 Recommended External Output circ

  19
• 7.2.3 Optical Interface Specifications

  19
• 7.3. Inputs and outputs table

  20
• 7.4. Configuring the GPIO module (regi

  21
• 7.4.1 Input/Output Signal Selector

  21
• 7.4.2 12-bit counter

  21
• 7.4.3 Pulse generators (20-bit x 4)

  22
• 7.5. GPIO programming examples

  23
• 7.5.1 GPIO Plus PWC shutter

  23
• 7.5.2 Internal Trigger Generator

  24
• 8. GigE®Vision Streaming Protocol (GVS

  25
• 8.1. Digital Video Output (Bit Allocat

  25
• 8.2. Bit Allocation (Pixel Format / Pi

  25
• 8.2.1 GVSP_PIX_RGB8_PACKED (RGB 24bit

  25
• 8.2.2 GVSP_PIX_RGB10V1_PACKED (RGB 32b

  26
• 8.2.3 GVSP_PIX_RGB10V2_PACKED (RGB 32b

  26
• 9. Functions and Operations

  26
• 9.1. GigE Vision Standard Interface

  26
• 9.2. Recommended Network Configuration

  26
• 9.2.1 Guide line for network settings

  27
• 9.2.2 Video data rate (network bandwid

  27
• 9.2.3 Note for setting packet size

  27
• 9.2.4 Calculation of Data Transfer Rat

  28
• 9.2.5 Note for 100BASE-TX connection

  29
• 9.3. Basic Functions

  29
• 9.3.1 Basic construction

  29
• 9.3.2 Modes of Operation

  30
• 9.3.3 Partial scan (Fast Dump ON)

  30
• 9.3.4 Vertical Binning (VB)

  32
• 9.3.5 Electronic shutter (SM)

  32
• 9.3.6 Auto-detect LVAL-sync / async ac

  33
• 9.4. Pre-processing functions

  34
• 9.4.1 Shading compensation

  34
• 9.4.2 White balance

  35
• 9.4.3 Linear matrix

  35
• 9.4.4 Blemish compensation

  36
• 9.4.5 Gamma setting (Look Up Table)

  36
• 9.4.6 Knee compensation

  36
• 9.5. Other functions

  37
• 9.5.1 Test pattern generator (Address

  37
• 9.5.2 Center marker

  37
• 9.6. Sensor Layout and timing

  38
• 9.6.1 CCD Sensor Layout

  38
• 9.6.2. Horizontal timing (Normal conti

  39
• 9.6.3 Vertical timing (Normal continuo

  39
• 9.6.4 Horizontal timing (Partial scan

  40
• 9.6.5 Vertical timing (Partial scan mo

  40
• 9.6.6 Horizontal timing (Vertical binn

  41
• 9.6.7 Vertical timing (vertical binnin

  42
• 9.7. Operating Modes - Timing

  42
• 9.7.1 Continuous operation

  42
• 9.7.2 Edge Pre-select Trigger Mode (EP

  43
• 9.7.3 Pulse Width Control Trigger Mode

  45
• 9.7.4 Reset Continuous Trigger (RCT)

  47
• 9.7.5 Sequential Trigger Mode (EPS)

  48
• 9.7.6 Delayed Readout EPS and PWC Mode

  49
• 9.7.7 Smearless mode

  50
• 9.7.8 Optical Black transfer mode

  51
• 9.7.9 Multi ROI mode (Multi Region of

  52
• 9.8. Mode and functions matrix

  52
• 10. External Appearance and Dimensions

  53
• 11. Specifications

  54
• 11.1. Camera sensitivity response

  54
• 11.2. Specification table

  55
• Register Map

  57
• Appendix

  68
• 1. Precautions

  68
• 2. Typical Sensor Characteristics

  68
• 3. Caution when mounting a lens on the

  68
• 4. Caution when mounting the camera

  69
• 5. Exportation

  69
• 6. References

  69
• Change history

  70
• User's Record

  71