Manuel D’UtilisationTable des matièresNotice3Warranty3Certifications3WARNING4Table of Contents5Table of Contents v5List of Figures vii5List of Tables ix51 Introduction 152 Installation 553 Operation 1554 Troubleshooting 2765 Appendix 296List of Figures7List of Tables9TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera11Operation Manual111 Introduction111.1 Product Description111.2 Features121.3 Functional Options131.4 System Configuration14FIGURE 1. TM-2016-8 System Configuration14FIGURE 2. Camera Link System Configuration142 Installation152.1 Getting Started152.1.1 Unpacking Instructions152.1.2 Components List152.1.3 Accessories and Options152.2 Camera Setup152.2.1 Heat Dissipation152.2.2 Connector Pin Configurations162.2.2 (a) 12-Pin Connector (TM-2016-8)16TABLE 1. 12-Pin Connector (TM-2016-8)162.2.2 (b) 12-Pin Connector (Camera Link models)17TABLE 2. 12-Pin Connector (TM-2016-8CL)172.2.2 (c) Digital Output Connector17FIGURE 3. Rear Panel View of Digital Connector172.2.2 (d) Camera Link Connector (Camera Link only)18TABLE 3. 31-Pin Connector (MP211-031-113-4300)18TABLE 4. Connector and Pinout Configurations192.2.2 (e) Analog Output Connector192.2.3 Shutter Speed Control Dial (TM-2016-8 only)20TABLE 5. Shutter Speed Control Dial202.2.4 RS-232 Communication Cable (TM-2016-8 only)20FIGURE 4. Serial Communication Cable RS-232B-12202.2.5 Digital Output Cable (TM-2016-8 only)21FIGURE 5. Pinout Configuration for Digital Output Cable212.2.6 Camera Link Cable (TM-2016-8CL only)222.2.7 Power Supplies and Power Cable Setup222.2.7 (a) Power Supplies222.2.7 (b) JAI, Inc. Power Cables23FIGURE 6. 12P-02S Interface Cable (optional)232.2.7 (c) “K” Series Power Supplies231. Attach the 110V line cord to the two terminals marked “AC.” Do not plug the cord into a 110V AC socket until you have completed steps 1 through 3.232. Attach the Gray and Yellow leads of the power cable to the Ground and 12V DC terminals, respectively.233. Replace the plastic terminal guard on the power supply.232.2.7 (d) Building Your Own Power Cable232.2.7 (e) Attaching the Power Cable to the Connector231. Rotate the connector while applying slight pressure until the keyways line up.242. Press the connector into place until firmly seated.243. Plug the power cord into the 100V AC socket. This will power the camera up.242.2.8 Attaching the Analog Video Output242.2.9 Attaching the Camera Lens243 Operation253.1 Camera Rear Panel (TM-2016-8)253.1.1 Up/Down Switch253.1.2 Digital Output Connector253.1.3 Analog Output Connector253.1.4 Power, RS-232, and External Sync Connector253.1.5 Shutter Speed Control Switch253.1.6 Mode Selection Switch25TABLE 6. Mode Selection Switch263.2 Camera Link Rear Panel (TM-2016-8CL)263.2.1 Digital Output Connector263.2.2 Analog Output Connector273.2.3 Power and External Sync Connector273.3 Progressive Scanning281. Progressive Scanning digital and analog output282. Double-speed scanning output (two-row binning)283.4 Electronic Shutter283.5 Integration293.6 Asynchronous Reset293.6.1 External VINIT With Pulse Width293.6.2 No Delay Shutter and Read-out-inhibit (ROI)303.6.3 Internal Shutter Speed Control313.7 Dynamic Range Control323.7.1 Programmable Look-Up Table (LUT) and Knee Control32FIGURE 7. Look-Up Table333.8 Scan Modes333.8.1 Full Progressive Scan333.8.2 Two-Row Binning333.9 External Sync and Pixel Locking333.10 Camera Timing Charts343.10.1 Pixel Clock Locking (optional)363.11 Serial Communication Kit (TM-2016-8)364 Troubleshooting374.1 Problems and Solutions374.1.1 Symptom: No Video374.1.2 Symptom: Dark Video374.1.3 Symptom: Non-synchronized Video374.2 Information and Support Resources385 Appendix395.1 Specifications39TABLE 7. TM-2016-8 and TM-2016-8CL Product Specifications Table39TM-2016-8 and TM-2016-8CL391”, 7.4µm x 7.4µm progressive scan interline transfer CCD391920 (H) x 1080 (V)3915.90 (H) mm x 8.61 (V) mm397.4µm x 7.4µm391920 x 1080 lines at 8Hz,391920 x 540 at 16Hz (two-row binning)39Internal/external auto switch39HD/VD, 4.0 Vp-p impedance 4.7K½39HD=9.09kHz±5%39VD=8Hz±5%, non-interlace3920.000 MHz39Digital: 1920 (H) x 1080 (V), Analog; over 1200 TV lines (H) x 800 TV lines (V)3950dB min. (AGC: off)392.0 lux f=1.439Sensitivity: 13µV/ e-39Analog: 1.0 Vp-p composite video, 75½39Digital output: 8-bit RS-644 output (A/D input from CCD: 10-bit)39Camera Link (TM-2016-8CL only)39OFF39Programmable LUT (1.0 std.)39C-mount (use 1” format lenses)39(Adjustable back focus: optional)3912V DC, 440mA (current measured at 25°)39-10°C to 45°C397 Grms (10Hz to 2000Hz)3970G, 10-11msec3944mm x 44mm 64mm (1.75” x 1.75” x 2.50”)39136 grams, 4.8 oz. (141gr, 5.0 oz.: CL version)39RS-644 output, adjustable back-focus front end3930DG-02 digital output cable,39CS-232E serial communication kit (TM-2016-8),3926CL-02-26 Camera Link output cable (TM-2016-8CL)3912P-02S39PD-12UU series (includes power connector)395.1.1 Physical Dimensions40FIGURE 8. Physical Dimensions (TM-2016-8)40FIGURE 9. Physical Dimensions (TM-2016-8CL)405.1.2 Spectral Response41FIGURE 10. Spectral Response41Taille: 1,7 MoPages: 44Language: EnglishOuvrir le manuel