Manuels d'utilisation pour Patton electronic 1080ARC

Table des matières

• 1.0 Warranty Information

  4
  • 1.1 FCC Information

    4
  • 1.2 CE Notice

    4
  • 1.3 Service

    5
• 2.0 General Information

  6
  • 2.1 Features

    6
  • 2.2 Description

    6
• 3.0 Configuration

  8
  • 3.1 Switch Locations and Orientation

    8
  • 3.2 Configuration Switch Set “S1”

    9
    • S1-1 through S1-4: Data Rate Setting

      9
    • S1-5 and S1-6: Clock Source

      10
    • S1-7: Asynchronous/Synchronous Mode

      10
    • S1-8: Carrier Control Method

      10
  • 3.3 Configuration Switch Set S2

    11
    • S2-2: 2-Wire/4-Wire Mode Selection

      11
    • S2-3: V.52 and V.54 Diagnostic Test

      11
    • S2-4 and S2-5: RTS/CTS Delay

      12
    • S2-6: Extended Signaling Rate

      12
    • S2-7 and S2-8: Word Length

      12
  • 3.4 Configuration Switch Set S3

    13
    • S3-1: Input Impedance

      14
    • S3-4: Mode Selection

      14
    • S3-5: RS-232 Initiation of Local Loopback Test

      14
    • S3-6: RS-232 Initiation of Remote Loopback Test

      15
    • S3-7 and S3-8: Antistream Control

      15
  • 3.5 Rear Card Configuration

    16
    • DB-25/RJ-11 & DB-25/RJ-45 Strap Settings

      17
    • Line Shield & FRGND (JB2)

      18
    • DTE Shield (Pin 1) & FRGND (JB3)

      18
    • SGND & FRGND (JB4)

      19
    • RJ-45/RJ-11 & RJ-45/RJ-45 Strap Settings

      19
    • Line Shield & FRGND (JB2)

      20
    • SGND & FRGND (JB5)

      20
    • DTE Interface Pin 2 (JB6)

      21
• 4.0 Installation

  22
  • 4.1 The Model 1000r16p Rack Chassis

    22
    • The Rack Power Supply

      22
    • Switching the Power Supply On and Off

      22
  • 4.2 Installing The Model 1080arc Into The Chassis

    23
  • 4.3 Wiring The Model 1080arc

    23
    • RS-232 Connection

      23
    • Twisted Pair Connection

      23
    • Point-to-Point Twisted Pair Connection

      24
    • Multipoint Twisted Pair Connection

      26
• 5.0 Operation

  27
  • 5.1 LED Status Monitors

    27
    • The “TD” and “RD” Indicators

      27
    • The “RTS” and “CD” Indicators

      28
    • The “Test” Indicator

      28
    • The “Error” Indicators

      28
    • Setting Up The “Error” LED To Test Cable Quality

      28
    • Reading The Test

      29
  • 5.2 Antistreaming Error Indicator

    29
  • 5.3 Power-up

    30
  • 5.4 Test Modes

    30
    • Local Analog Loopback (LAL)

      30
    • Remote Digital Loopback (RDL)

      31
    • Using The V.52 BER Test Independently

      32
• Appendix A Specifications

  33
• Appendix B Cable Recommendations

  34
• Appendix C 1080ARC Factory Replacement Parts

  36
• Appendix D 1080ARC Interface Standards

  37