Manuels d'utilisation pour Pelco C561M-F

Table des matières

• Important Safeguards and Warnings

  2
  • 1. Read these instructions.

    2
  • 2. Keep these instructions.

    2
  • 3. Heed all warnings.

    2
  • 4. Follow all instructions.

    2
  • 5. Installation should be done only by qualified service personnel and conform to all local codes.

    2
  • 6. Use only installation methods and materials capable of supporting four times the maximum specified load.

    2
  • 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

    2
  • 8. Only use attachments/accessories specified by Pelco.

    2
  • 9. Use only with the cart, stand, tripod, bracket, or table specified by Pelco, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

    2
  • 10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, su...

    2
  • 11. Only use parts recommended by Pelco.

    2
  • 12. Use stainless steel hardware to fasten the enclosure to outdoor surfaces.

    2
  • 13. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building (permanent 240 VAC product only).

    2
• Description

  3
• Installation

  4
  • MOUNTING INSTRUCTIONS

    4
    • 1. Remove the retaining screw from the door latch of the WCS1-4 power supply.

      4
    • 2. Open the door of the WCS1-4 power supply, and then remove the plug(s) from the required conduit hole(s) located on the bottom of the unit. Install 3/4-inch (1.91 cm) conduit fitting(s) (not supplied). Close the lid to the power supply.

      4
    • 3. Determine the mounting location for the WCS1-4.

      4
    • 4. Use the WCS1-4 power supply as a template and mark the four fastener positions on the mounting surface.

      4
    • 5. Prepare the holes for installation.

      4
    • 6. Attach the WCS1-4 power supply securely to the mounting surface with four fasteners of appropriate length. Fasteners between 1/4-inch and 5/16-inch diameter (not supplied) can be used.

      4
    • Figure 1.

      4
    • Figure 2.

      4
    • Figure 3.

      4
  • Fuse Installation

    5
  • input power wiring

    5
    • 1. Determine the size of the input wire needed.

      5
    • 2. Bring the wiring into the WCS1-4 through the conduit fitting.

      5
    • 3. Attach the neutral input power wire to the 100V, 120V, or 240V NEUTRAL connection on the Primary Line Input connector strip. Attach the hot wire to the LINE connection on the same strip.

      5
    • 4. Attach the input ground wire to the No. 6 ground stud, located between the conduit holes, and tighten the wire with the nut and washer (supplied).

      5
  • Output wiring

    6
    • 1. Refer to Table A and determine the output connection needed for your camera, dome, or positioning system. Refer to Figure 4, for the proper connector strip connections.

      6
    • 2. Attach one output wire to either the Tap A (24 VAC), Tap B (26 VAC), or Tap C (28 VAC) connections on the Secondary Output Ta...

      6
    • 3. Close the lid to the WCS1-4 power supply, replace the retaining screw to the door latch, and then turn power on.

      6
    • Figure 4. Wiring Connector Diagram

      6
  • Cable Connections and requirements

    7
    • Table A. Wiring Distances

      7
      • 1. Pick the unit type.

        7
      • 2. Find the wire gauge used (22 gauge is not recommended).

        7
      • 3. Determine which secondary output tap (A, B, or C) is appropriate for the distance between the dome or positioning system and the WCS1-4. Distance is in feet (meters).

        7
• Maintenance

  8
• Specifications

  9
  • Electrical

    9
  • mechanical

    9
  • General

    9
    • Figure 5. WCS1-4 Dimension Drawing

      10