Manuels d'utilisation pour RF-Link Technology NL6000

Table des matières

• Product Overview

  6
• 1.1. Features

  7
• Regulatory Information

  9
• Specifications

  11
• Hardware Installation and Operation

  13
• 4.1. Parts Description

  13
• 4.2. Power Connections

  13
• 4.3. Serial Port

  13
• 4.4. Antenna Connection

  15
• 4.5. LEDs

  15
• 4.6. Operation

  15
• 4.7. Technical Support

  16
• Software Configuration

  16
• 5.2. Preparation

  16
• 5.3. Unique Data Requirements for a Base Station

  17
• 5.4. Source and Destination Addressing

  17
• 5.5. Behavior of Repeater Units

  18
• 5.6. Packet Data Options

  21
• 5.6.1. Transmission Mode

  23
• 5.6.2. Maximum Packet Size

  24
• 5.6.3. Over-the-Air Data Rates

  24
• 5.6.4. Acknowledgements

  24
• 5.6.5. Carrier Sense Multiple Access

  25
• 5.7. Serial Connection to an I/O Device

  25
• 5.7.1. Basic Serial Parameters

  25
• 5.7.2. Flow Control

  25
• 5.7.3. DCD Mode

  26
• 5.7.4. Pre- and Post-Data DCD Time

  26
• 5.8. Planning the RF Channel

  26
• 5.9. Factory Default Parameters

  26
• Procedures .

  27
• 6.1. General Procedures

  28
• Entering Programming Mode

  28
• Setting the Program Mode

  28
• Saving Configuration Changes to Flash Memory

  28
• Saving Configuration Changes Temporarily

  28
• Reverting to the Prior Configuration

  28
• Returning to the Previous Menu

  29
• Displaying the Configuration Summary Window

  29
• 6.2. Radio Network Setup

  30
• Setting the Unit Type

  30
• Setting the Unit ID (MYID)

  30
• Setting the Target Unit ID (TOID)

  30
• Setting the Active Channel

  30
• Setting the Receive Frequency

  30
• Setting the Transmit Frequency

  30
• 6.3. Serial Connection Setup

  31
• Setting the Baud Rate

  31
• Setting the Data Bits

  31
• Setting the Stop Bits

  31
• Setting the Transmit Character Timeout

  31
• Setting the Flow Control Option

  31
• Setting the DCD Mode

  31
• Setting the Pre-Data DCD Time

  32
• Setting the Post-Data DCD Time

  32
• Setting the Maximum Packet Size

  32
• Setting the Packet Mode

  32
• Setting the Data Rate

  33
• Setting the Request ACKs Option

  33
• Setting the Contention Option

  33
• Setting the Max Retries Option

  33
• 6.5. Repeater Setup

  34
• Selecting the Repeater Entry to Edit

  34
• Setting the Repeater Trigger

  34
• Setting the Repeater Trigger ID

  35
• Setting the Repeater Transmit Channel

  35
• Setting the Repeater Transmit Delay

  35
• 6.6. File Management

  35
• Downloading a Software Upgrade .

  35
• Saving Parameters to Disk

  36
• Restoring Parameters from Disk

  36
• Restoring Default Parameters

  37
• Menu Quick Reference

  38
• 7.1. Main Menu

  38
• 7.2. Summary Window

  38
• 7.3. Serial Menu

  39
• 7.4. DCD232 Sub-Menu

  39
• 7.5. Network Menu

  40
• 7.7. Radio Menu

  41
• 7.8. Diagnostics Menu

  41
• 7.9. Save/Restore Parameters Menu

  42
• Other Considerations

  43
• 8.2. Troubleshooting

  43
• 8.2.1. Use a Good Antenna

  43
• 8.2.2. Three-wire Interface

  43
• 8.2.3. Hardware Flow Control

  43
• 8.2.4. Use a Fully-Wired RS-232 Cable

  44
• 8.2.5. Use a Slower Baud Rate .

  44
• 8.2.6. Use a Faster Baud Rate

  44
• 8.2.7. Unit Does Not Enter Programming Mode

  44
• 8.1. Duty Cycle

  45
• Appendix A Diagnosing and Correcting Performance Problems

  45
• Setting the Power Value

  45
• Setting the Frequency Trim (includes setting Power)

  45
• Setting the Deviation and Balance

  46
• Setting the Receive Gain

  47
• Appendix B - Factory Default Parameters

  49
• Index

  50