Manuel D’UtilisationTable des matièresSECTION 1: Heater Safety1SECTION 12: Control Methods421.1 Manpower Requirements112.1 ROBERTS GORDON® System Control42SECTION 2: Installer Responsibility212.2 ROBERTS GORDON® ULTRAVACTM422.1 Wall Tag212.3 SPST Transformer Relay (P/N 90417600)422.2 Corrosive Chemicals212.4 DPST Transformer Relay (P/N 90436300)422.3 National Standards and Applicable Codes2SECTION 13: Starting The System49SECTION 3: Critical Considerations313.1 Checking the Gas Line493.1 Required Clearances to Combustibles313.2 Checking the Electrical System49SECTION 4: National Standards and Applicable Codes713.3 Starting the System494.1 Gas Codes713.4 Setting the Vacuum494.2 Aircraft Hangars7SECTION 14: Operation and Maintenance514.3 Public Garages714.1 Sequence of Operation514.4 Electrical714.2 To Shut Off Heater514.5 Venting714.3 To Start Heater514.6 High Altitude7SECTION 5: Major Components814.5 Maintenance Checklist525.1 Standard Parts List11SECTION 15: Troubleshooting55SECTION 6: Design Requirements1315.1 Troubleshooting Flow Chart55SECTION 7: Heater Installation15SECTION 16: Replacement Parts577.1 Tube Installation16SECTION 17: General Specifications587.2 Coupling and Tube Assembly1617.1 Material Specification587.3 Elbow Package Configuration1717.2 Heater Specifications587.4 Reflector Installation1817.3 Suspension Specifications587.5 Burner Installation2017.4 Controls Specifications58SECTION 8: Optional Heater Accessories218.1 Tee Installation21Limited Warranty618.2 Reflector Joint218.3 Reflector Side Extension238.4 Universal Shield248.5 Barrier Shield248.6 Two-Foot Decorative Grille Installation258.7 One-Foot Decorative Grille Installation268.8 Protective Grille Installation298.9 Classic Cast-Iron Components30SECTION 9: Pump Installation and Venting319.1 Pump Installation31EP-200 and EP-300 Series Pumps329.3 Horizontal Venting 4" (10 cm) Pipe34SECTION 10: Outside Air Supply3710.1 Pressurized3710.2 Non-Pressurized3710.3 Outside Air Blower Internal Wiring38SECTION 11: Gas Piping41Figure 1: Standard Reflector4Figure 2: One Side Reflector4Figure 3: Two Side Reflectors4Figure 4: Universal Shield, Position 15Figure 5: Universal Shield, Position 25Figure 6: Universal Shield, Position 35Figure 7: 2-Foot Deco Grille6Figure 8: Barrier Shield6Figure 9: 1-Foot Deco Grille6Figure 10: Major Component Descriptions8Figure 11: Heater Assembly Overview14Figure 12: Critical Hanger Placement15Figure 13: Reflector Joint Detail22Figure 14: EP-200 Condensate Valve Assembly31Figure 15: Vertical Venting Configuration33Figure 16: EP-100 Horizontal Venting Configurations34Venting Configurations35Venting Configurations36Figure 19: Duct Sizing37Figure 20: Outside Air Blower Internal Wiring Diagram38Figure 21: Filter Housing Assembly38Figure 22: Air Supply Blower Support39Figure 23: Pressurized Outside Air Supply39Figure 24: Non-Pressurized Outside Air Supply40Figure 25: Gas Connection with Flexible Gas Hose41Figure 26: One Zone Operation without Control Panel43without Control Panel44Figure 28: Two Zone Operation without Control Panel45Figure 29: General System Wiring46120 V 1 Ø Pump46120 V 1 Ø Pump47EP-303 208 V - 230 V (or 460 V) 3 Ø Pump47Figure 33: Burner Internal Wiring48Figure 34: Burner Internal Ladder Diagram48Figure 35: Vacuum Reading50Taille: 11 MoPages: 72Language: EnglishOuvrir le manuel