Manuels d'utilisation pour Roberts Gorden TF-300

Table des matières

• SECTION 1: Heater Safety

  1
• SECTION 10: Gas Piping

  40
• 1.1 Manpower Requirements

  1
• SECTION 11: Wiring

  41
• SECTION 2: Installer Responsibility

  2
• 11.1 Line Voltage Thermostat Wiring

  41
• 2.1 Wall Tag

  2
• 11.2 Low Voltage Thermostat and Relay Wiring

  42
• 2.2 Corrosive Chemicals

  2
• 11.3 Internal Wiring

  42
• 2.3 National Standards and Applicable Codes

  2
• 11.4 Ladder Diagram

  43
• SECTION 3: Critical Considerations

  3
• 11.5 Electrical Connection to the Burner

  43
• 3.1 Required Clearances to Combustibles

  3
• SECTION 12: Operation and Maintenance

  44
• SECTION 4: National Standards and Applicable Codes

  7
• 12.1 Sequence of Operation

  44
• 4.1 Gas Codes

  7
• 12.2 To Shut Off Heater

  44
• 4.2 Aircraft Hangars

  7
• 12.3 To Start Heater

  44
• 4.3 Public Garages

  7
• 4.4 Electrical

  7
• 12.5 Maintenance Checklist

  45
• 4.5 Venting

  7
• SECTION 13: Troubleshooting

  47
• 4.6 High Altitude

  7
• 13.1 Troubleshooting Flow Chart

  47
• SECTION 5: Major Components

  8
• 13.2 Manifold Gas Pressure Setting

  49
• 5.1 Standard Parts List

  9
• SECTION 14: Replacement Parts

  50
• SECTION 6: Suggested Layouts

  11
• SECTION 15: General Specifications

  52
• 6.1 TF-380 - 4 Elbow Design (Common Vent)

  11
• 15.1 Material Specification

  52
• 6.2 TF-350 - 4 Elbow Design (Common Vent)

  11
• 15.2 Heater Specifications

  52
• 6.3 TF-300 - Double "U" Design (Common Vent)

  11
• 15.3 Suspension Specifications

  52
• 6.4 TF-160 - Single Elbow Design (Individual Vents)

  12
• 15.4 Controls Specifications

  52
• 6.5 TF-160 Double "L" Design (Individual Vents)

  12
• Warranty

  53
• (Individual Vents)

  12
• SECTION 7: Heater Installation

  13
• 7.1 Burner Tube Installation

  18
• 7.2 Burner Installation

  18
• 7.3 Tube Clamp Package Installation

  19
• 7.4 Coupling and Tube Assembly

  19
• 7.5 Turbulator Installation

  21
• 7.6 Reflector Installation

  21
• SECTION 8: Optional Heater Accessories

  23
• 8.1 U-Tube Configuration

  23
• 8.2 Elbow Package Configuration

  26
• 8.3 Reflector Side Extension

  28
• 8.4 Lower Clearance Shield Installation

  29
• 8.5 Two-Foot Decorative Grille Installation

  29
• 8.6 One-Foot Decorative Grille Installation

  31
• 8.7 Protective Grille Installation

  33
• SECTION 9: Venting

  34
• 9.1 Venting Requirements

  34
• 9.2 Horizontal Ventilation 4" (10 cm) Pipe

  35
• 9.3 Vertical Ventilation 4" (10 cm) Pipe

  35
• 9.4 Flexible Boot Installation (Single Vent)

  36
• 9.5 Common Sidewall Venting

  36
• 9.6 Vertical Ventilation 6" (15 cm) Pipe

  37
• 9.7 Flexible Boot Installation (Common Vent)

  37
• 9.8 Outside Combustion Air Supply

  38
• Figure 1: Standard Reflector

  3
• Figure 2: One Side Reflector

  4
• Figure 3: Two Side Reflectors

  4
• Figure 4: 45° Tilt Reflector

  4
• Figure 5: U-Tube, Standard Reflector

  5
• Figure 6: U-Tube, 45°

  5
• Figure 7: U-Tube, Opposite 45° Reflector

  5
• Protective Grille

  6
• Figure 9: Lower Clearance Shield

  6
• Figure 10: Venting

  6
• Figure 11: Major Component Descriptions

  8
• Figure 12: Critical Hanger Placement

  14
• Figure 13: Linear Heater Assembly Overview

  15
• Figure 14: Linear Heater Layout Overview

  16
• Figure 15: Linear Heater Layout Overview (Continued)

  17
• Figure 16: U-Tube Heater Assembly Overview

  23
• Figure 17: U-Tube Heater Layout Overviews

  24
• Figure 18: U-Tube Heater Layout Overviews (Continued)

  25
• Figure 19: Reflector Joint Detail

  27
• Figure 20: Gas Connection with Flexible Gas Hose

  40