Manuels d'utilisation pour TANDBERG MSE 8350

Table des matières

• Table of contents

  4
• General information

  5
  • About the MSE 8350 IP GW blade

    5
  • Port and LED location

    5
    • Figure 1: IP GW blade front panel

      5
  • LED behavior

    6
    • Table 1: IP GW blade LED behavior

      6
• Installing the IP GW blade

  8
  • Step one: Install the IP GW blade into the MSE 8000 chassis

    8
    • 1 Remove the blade or blanking blade from the slot into which you are going to install the IP GW blade:

      8
      • 2 Open both retaining latches on the front of the IP GW blade. When open, a retaining latch is at a 90 angle perpendicular to the front of the blade.

        8
      • 3 Slide the IP GW blade into the blade slot (as shown in Figure 2) until it stops.

        8
      • 4 Simultaneously close both retaining latches on the blade (thereby engaging the connectors at the rear of the blade) to secure in the chassis as shown in Figure 3.

        8
      • 5 Using a No.1 Phillips screwdriver, tighten the screws in the retaining latches with a clockwise quarter turn.

        9
        • Figure 2: Inserting a blade into the chassis

          9
        • Figure 3: Closing the retaining latches on the front of a blade

          9
  • Step two: Connect to Ethernet Ports A and B

    10
• Initial configuration

  11
  • Step one: Configure Ethernet Ports A and B

    11
  • Step two: Configure the default gateway and routes (optional)

    11
    • 1 Log in to the Supervisor and go to Hardware > Blades.

      11
      • 2 Click the name of the IP GW blade and select the Routes tab.

        11
• Configuring the IP GW blade

  12
  • Step one: Log in to the IP GW blade

    12
    • 1 Log in to the Supervisor’s web interface.

      12
      • 2 Go to Hardware > Blades and click the IP address of the IP GW blade.

        12
      • 3 Click Click here to log in, and then click Change log in and enter the user name admin with no password.

        12
  • Step two: Configure an H.323 gatekeeper or SIP registrar (optional)

    12
  • Step three: Configure the auto attendant menus (optional)

    13
  • Step four: Configure an operator (optional)

    13
  • Step five: Add endpoints and call groups (optional)

    14
  • Step six: Configure the dial plan

    14
• Checking for updates

  15
  • 1 Log in to the IP GW blade web interface and go to Status > General.

    15
    • 2 Make a note of the software version that is currently installed.

      15
    • 3 Go to the support section of the web site and check if a more recent release is available for the IP GW blade.

      15
    • 4 If a more recent release is available, download it and save it locally.

      15
  • 1 Unzip the software release file that you downloaded.

    15
    • 2 In the IP GW blade web interface, go to Settings > Upgrade.

      15
    • 3 In the Main software image section, click Browse and locate the unzipped file.

      15
    • 4 Click Upload software image. The browser begins uploading the file to the IP GW blade, and a new browser window opens to indicate the progress of the upload.

      15
    • 5 Click Shut down IP GW, confirm shut down, and restart the IP GW blade.

      15
• Troubleshooting and technical support information

  16
  • Using the event log to help solve a problem

    16
  • Getting more help

    16
    • 1 Refer to the Technical FAQ section of the web site. We keep the Technical FAQ section up to date with the latest information from our technical support team regarding the resolution of customer issues.

      16
      • 2 Contact your reseller. Our resellers have a wealth of experience with our products and this is often a quick way of solving a problem.

        16
      • 3 If your query remains unsolved, there is a web form in the Support area of the web site that you can complete. Ensure that you provide all the details requested by the form to assist the technical support team in resolving your problem:

        16