Manuel D’UtilisationTable des matières1. Overview of The DeviceNet Module191.2 Network Configuration of DeviceNet211.2.1 The Network Configuration211.2.2 Trunk Line/Drop Line and Maximum Cable Length221.2.3 The Terminal Resistor241.3 Conformity Specification and Trademarks251.4 The Basic Functions261.4.1 The Polling Instruction/Response Mode261.4.2 The Bit Strobe Instruction/Response Mode271.4.3 Synchronization/Asynchronous Mode and Data Update Cycle281.5 The DN211 Specification301.5.1 The Function Specification301.5.2 Number of Mounting Modules312. Names and Functions of DN211 Parts332.1 Outer Dimensions and Sizes332.2 Names of DN211 Parts342.3 Functions of DN211 Parts363. Preparation for Operation (hardware)383.1 DN211 Setting Flowchart (hardware)383.2 Switch Setting393.2.1 DIP Switch for Setting the Operation Mode/Communication Rate393.2.2 Rotary Switch for Node Address Setting413.3 Mounting in the Base Unit423.4 Connection with the Network433.4.1 Connecting DeviceNet Cables to Network Side Connectors443.4.2 Connecting the Network Side Connector to the DN211453.5 The Network Power/Grounding473.5.1 The Network Power Mechanism473.5.2 How to Configure Network Power Units483.5.3 The Network Power Unit (24 Vdc)543.5.4 The Network Grounding553.5.5 Procedure for Switching-ON/Shutting-OFF the Power563.6 The Network Components574. How to Handle Your DN211 (software)604.1 Configuration of the DN211 Communication Memory614.2 The Input/Output Data Area624.3 The RAS Information Area664.4 Allocating Slave Device Data to the Input/Output Data Area754.5 The Semaphore Area764.6 Requests to the DN21179The DN211 Operation Modes80Reset Request81Parameter Setting Request (local node)82Parameter Setting Request (slave device)85Operation Mode Control Request88RAS Information Read Request89Time Setting Request904.7 Completion Status915. Example of DN211 Applications925.1 The DN211 Operation Order925.2 Module Setting Procedure93Accessing the DN211 in Module Setting94Configuration of a Module Setting Sample Program96Reset Request97Parameter Setting Request (local node)99Parameter Setting Request (slave device)100Operation Mode Control Request106RAS Information Read111Time Setting Request1145.3 Slave Data Input/Output1165.3.1 Slave Device Check1165.3.2 Asynchronous Mode Data Input/Output1175.3.3 Synchronous Mode Data Input/Output1226. RAS Information (except RAS area on communication memory)1296.1 Module Status / Network Status LED (MS/NS)1306.2 Indications of the 7-Segment LED1316.3 RAS Information Reading Data1336.3.1 The RAS Counter1336.3.2 Event History1366.3.3 Execution Node Information1397. Troubleshooting1417.1 When Starting up the Module1417.2 Reset Request (scan list clear)1427.3 When the Module Doesn't Become Run Mode1437.4 Data Communication with Slave Devices1468. Installation/Wiring Work1488.1 Installation Environment and Mounting in the Base Unit1488.2 Mounting/Removing the Module1488.3 Power Unit Wiring/Grounding1498.3.1 Power Unit Wiring1498.3.2 Grounding1498.4 Network Installation1508.4.1 Installation Gists Outside the Board1508.4.2 Installation Gists Inside the Board153Maintenance and Inspection154READ/WRITE Instruction Execution Time156DN211A157Taille: 750 koPages: 173Language: EnglishOuvrir le manuel
Manuel D’UtilisationTable des matièresSafety Precautions3Usage Recommendations9Before Reading This Document11Contents131. Ethernet Port Overview151.1 System Configuration Using the Ethernet Port151.2 LAN Standards and Terminology161.3 Basic Functionality171.4 Ethernet Port Specifications221.5 Software Organization232. Ethernet Port Parts and Functions252.1 Front Panel252.2 Component Functions263. Preparing for Operation (Hardware)273.1 Connecting to the Network283.2 Network Wiring Equipment294. Preparing for Operation (Software)324.1 Ethernet Port Setup Flowchart (Software)324.2 Ethernet Port Instruction Specifications334.3 Ethernet Port Reset404.4 Parameter Setup Request424.5 Operating Mode Control Requests475. Computer Link Protocol and the PC Link Protocol Transmission515.1 Computer Link Protocol Transmission515.2 Sample Computer Link Protocol Program525.3 PC Link Protocol Transmission (Data write)585.4 PC Link Protocol Transmission (Data read)625.5 Sample PC Link Protocol Transmission Program656. Socket Interface Communication696.1 Overview696.2 Ethernet Port Socket Interface Usage Notes736.3 Socket Interface Information836.4 Using the Ethernet Port Socket Interface856.5 Sample Programs1137. RAS Information1237.1 T2N Special Relays and Registers1247.2 Down Information1267.3 Remote Port Verification Request1277.4 Remote Port Loopback (for an Ethernet Port)1297.5 Time Setting1317.6 RAS Information Readout1338. Error Handling1418.1 LED Display1418.2 Status (error status)1448.3 T2N Special Relays and Registers1478.4 Socket Interface Information1488.5 Troubleshooting1499. Installation and Wiring1649.1 Installation Environment and Base Unit Mounting1649.2 Network Wiring165Appendix170Appendix 1 Maintenance and Inspection170Appendix 2 Request Code Table172Appendix 3 Status Table173Appendix 4 Limitations on the T2N SEND and RECV Instructions176Taille: 640 koPages: 179Language: EnglishOuvrir le manuel
