Manuels d'utilisation pour UTC Fire & Security Americas Corporation Inc 844-PIR

Table des matières

• Sentrol AP750W Wireless PIR Motion Sensor

  1
• Product Summary

  1
• Installation

  1
  • Figure 1. Overhead (Bird’s Eye View) Detection Path

    1
  • Note The cardboard undercrawl mask should remain installed when sensor jumper J1 is set to the BI position. See the section “Setting the Sensor Cover age Area and Sensitivity” for complete information on sensor jumper settings.

    2
    • Tools and Supplies Needed

      2
• Mounting the Motion Sensor

  2
  • Note Remove the factory-installed plastic masks before mount ing. Re-install as desired after walk testing.

    2
    • 1. Remove the small cover (see Figure 4)

      2
    • 2. Open the sensor housing by pressing down on the top rear and pulling the front cover at the top (see Figure 5). Set the front cover aside

      2
  • Note Avoid touching the mirror. Fingerprints may affect detection coverage.

    3
    • 3. Mount the sensor on a flat wall or in a corner, using the appropriate mounting holes (see Fig ure 6). Use wall anchors and screws to secure the sensor.

      3
      • Figure 6. Mounting Hole Locations

        3
• Setting the Sensor Coverage Area and Sensitivity

  3
  • Note Do not use the bi-curtain mode for detection in areas within 5 feet of the sensor. When selecting bi-curtain mode, always leave the cardboard undercrawl mask installed.

    3
    • Figure 7. Sensitivity Mode and Coverage Area Jumper Settings

      3
• Walk Testing

  3
  • 1. Remove the sensor cover to activate the tamper switch, then reattach it to activate the 2- minute walk test mode.

    3
  • 2. Walk across the coverage pattern to determine the coverage area, indicated by LED activation.

    3
  • Environment Testing

    4
• Installing Masks

  4
  • Self-Adhesive Masks

    4
    • Figure 8. Installing Self-Adhesive Masks

      4
  • Plastic Masks

    4
  • Note After installing masks, always conduct a walk test and environment test to ver ify the coverage area is cor rect for the application.

    4
    • Figure 9. Installing Plastic Masks

      4
• Programming

  5
  • 1. Put the panel into program mode.

    5
  • 2. Advance to the learn sensors menu.

    5
  • 3. Enter the appropriate sensor group and desired sensor number.

    5
  • 4. When the panel prompts you to trip the sensor, activate the sensor tamper switch by removing the sensor cover.

    5
  • 5. Reattach the sensor cover.

    5
  • 6. Exit from program mode.

    5
• Final Testing

  5
  • 1. After the sensor has been mounted, remove the sensor cover to trip the tamper switch and acti vate the walk test mode.

    5
  • 2. Replace the sensor cover.

    5
  • 3. Place the control panel in test mode.

    5
  • 4. Move across the detection pattern until the sensor LED turns on, then STOP your motion.

    5
  • 5. Listen for the appropriate system response. If the system does not respond, proceed to the “Troubleshooting” section.

    5
• Maintenance

  5
  • Replacing Batteries

    5
    • 1. Remove the sensor cover (see Figures 4 and 5) and set it aside.

      5
    • 2. Remove the transmitter (upper) circuit board battery (see Figure 10)

      5
    • 3. Remove the transmitter circuit board and place it inside the cover (see Figure 11)

      5
  • Note Avoid touching the mirror. Fingerprints may affect detection coverage

    6
    • 4. Carefully remove the PIR (lower) circuit board by pressing outward on either side tab, then pull up on the circuit board (see Figure 12).

      6
      • Figure 12. Removing the PIR Circuit Board

        6
    • 5. Remove the PIR circuit board battery (located on opposite side of components) and install a new one, observing polarity (marked on the circuit board).

      6
    • 6. Re-install the PIR circuit board into the sensor plastic.

      6
    • 7. Re-install the transmitter circuit board onto the PIR circuit board.

      6
    • 8. Install a new battery in the transmitter circuit board, observing polarity (marked in battery bucket).

      6
• Lithium Battery Disposal

  6
• Troubleshooting

  6
• Specifications

  7
• Notices

  7
  • These devices comply with part 15 of the FCC rules. Operation is subject to the following two conditions:

    7
  • 1. These devices may not cause harmful interference.

    7
  • 2. These devices must accept any interference received, including interference that may cause undesired operation.

    7
  • Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the users’ authority to operate the equipment.

    7
  • FCC ID: B4Z-844-PIR

    7
  • U.S. Patent Nos: 4,855,713, 4,864,636, 5,761,206, 5,805,063, 5,872,512, and 5,942,981

    7
    • Model No.

      1
    • Document Number: 466-22XX Rev. September 2004 PRELIMINARY

      1
  • Preliminary 9/1/04

    1