Manuels d'utilisation pour Viewsonic PJ551D-2

Table des matières

• Introduction

  7
  • Projector Features

    7
  • Package Contents

    8
• Projector with Lens Cap

  8
• AC Power Cord

  8
• VGA Cable (D-SUB to D-SUB)

  8
• User’s Manual

  8
  • Projector Overview

    9
• Using the Product

  11
  • Control Panel

    11
  • Connection Ports

    12
  • Remote Control

    13
• For the first time use:

  14
• For battery change:

  14
  • 1. Push the catch to the right and remove the battery holder.

    14
  • 2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.

    14
  • 3. Push the battery holder back into the remote control until you feel a click.

    14
  • Remote Control Operation

    15
  • Installation

    16
    • Connecting the Projector

      16
    • Powering On/Off the Projector

      17
• Powering On the Projector:

  17
  • 1. Remove the projector lens cap.

    17
  • 2. Complete the AC power cord and peripheral signal cable(s) connections.

    17
  • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.

    17
  • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.

    17
• Powering Off the Projector:

  17
  • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.

    17
  • 2. Press button again to confirm.

    17
  • 3. Disconnect the AC power cord from the electrical outlet and the projector.

    17
  • 4. Do not turn on the projector immediately following a power off procedure.

    17
  • Adjusting the Projector

    18
• Adjusting the Projector Height

  18
  • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.

    18
  • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.

    18
• Adjusting the Projector Zoom and Focus

  18
  • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

    18
  • 2. Adjust the image by sliding the zoom ring.

    18
• Adjusting Projection Image Size

  19
  • Menu Operation

    20
    • 1. Press the Menu button to open the OSD menu.

      21
    • 2. When OSD is displayed, use p / q to select any feature in the main menu.

      21
    • 3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.

      21
    • 4. Adjust the settings with t / u.

      21
    • 5. Press the Menu button, the screen will return to the main menu.

      21
    • 6. To exit OSD, Press the Menu button again. The OSD menu will close and the projector will automatically save the new settings.

      21
  • Maintenance

    24
    • Cleaning the Lens

      24
    • Cleaning the Projector Housing

      24
    • Replacing the Lamp

      25
      • 1. Turn off the projector.

        26
      • 2. If the projector is installed in a ceiling mount, remove it from the mount.

        26
      • 3. Unplug the power cord.

        26
      • 4. Loosen the screw in the side of the lamp cover and remove the cover.

        26
      • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.

        26
      • 6. Insert the new lamp module into the projector and tighten the screws.

        26
      • 7. Replace the lamp cover and tighten the screw.

        26
      • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

        26
      • 9. Reset the lamp hour. Refer to the “Setting” menu.

        26
  • Appendix

    28
    • LED Indicator Messages

      28
    • Compatibility Modes

      29
• Computer:

  29
• Video:

  29
  • Troubleshooting

    30
• Start-up problems

  30
• Image problems

  30
• Notes on the AC Power Cord

  7