Manuels d'utilisation pour Viewsonic pjd6210

Table des matières

• Introduction

  8
  • Projector Features

    8
  • Package Contents

    9
• Projector with Lens Cap

  9
• AC Power Cord

  9
• VGA Cable (D-SUB to D-SUB)

  9
  • Projector Overview

    10
• Using the Product

  12
  • Control Panel

    12
  • Connection Ports

    13
  • Remote Control

    14
  • Replacing the Battery

    15
    • 1. Push the catch to the left and remove the battery holder.

      15
    • 2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.

      15
    • 3. Push the battery holder back into the remote control until you feel a click.

      15
  • Remote Control Operation

    16
• Installation

  17
  • Connecting the Projector

    17
  • Powering On/Off the Projector

    18
• Powering On the Projector:

  18
  • 1. Remove the projector lens cap.

    18
  • 2. Complete the AC power cord and peripheral signal cable(s) connections.

    18
  • 3. Press button on the control panel or the POWER button on the remote control to turn on the projector. The projector takes a minute or so to warm up.

    18
  • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.

    18
• Powering Off the Projector:

  18
  • 1. Press button on the control panel or the POWER button on the remote control to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.

    18
  • 2. Press button on the control panel or the POWER button on the remote control again to confirm.

    18
  • 3. Disconnect the AC power cord from the electrical outlet and the projector.

    18
  • 4. Do not turn on the projector right after power off.

    18
  • 5. This projector supports Off-To-Go function. User can safely cut off the power source immediately without causing harm to the projector lamp.

    18
  • Adjusting the Projector

    19
• Adjusting the Projector Height

  19
• Adjusting the Projector Zoom and Focus

  19
  • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

    19
  • 2. Adjust the image by sliding the zoom ring.

    19
• Adjusting Projection Image Size

  20
  • Menu Operation

    21
    • 1. Press the MENU button to open the OSD menu.

      22
    • 2. When OSD is displayed, use p / q to select any feature in the main menu.

      22
    • 3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.

      22
    • 4. Adjust the settings with t / u.

      22
    • 5. Press the MENU button, the screen will return to the main menu.

      22
    • 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.

      22
  • Maintenance

    25
    • Cleaning the Lens

      25
    • Cleaning the Projector Housing

      25
    • Replacing the Lamp

      26
      • 1. Turn off the projector.

        27
      • 2. Unplug the power cord.

        27
      • 3. Loosen the screw in the lamp cover and remove the cover.

        27
      • 4. Loosen the two screws from the lamp module.

        27
      • 5. Pull up the handle, and then pull out the lamp unit by the handle.

        27
      • 6. Insert a new lamp module into the projector and tighten the screws.

        27
      • 7. Replace the lamp cover and tighten the screw.

        27
      • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

        27
      • 9. Reset the lamp hour. Refer to the Setting (Computer / Video Mode) menu.

        27
  • Specifications

    28
  • Appendix

    29
    • LED Indicator Messages

      29
    • Compatibility Modes

      30
• Computer:

  30
• Video:

  30
  • Troubleshooting

    31
• Start-up problems

  31
• Image problems

  31
  • RS-232 Command and Configuration

    32
  • IR Control Code

    33