Yamaha RX-V1000RDS Manuale Utente
19
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC OPERA-
TION
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
CONNECTIONS
IMPEDANCE SELECTOR Switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch
only when this unit is in the standby mode.
only when this unit is in the standby mode.
Switch
position
position
Speaker
Impedance level
If you use one set of main speakers, the impedance of each
speaker must be 4
speaker must be 4
Ω
or higher.
The impedance must be 6
Ω
or higher.
The impedance of each speaker must be 8
Ω
or higher.
IMPEDANCE SELECTOR
If you use two sets of main speakers, the impedance of
each speaker must be 8
each speaker must be 8
Ω
or higher.
Center
Rear
The impedance of each speaker must be 6
Ω
or higher.
Main
If you use one set of main speakers, the impedance of each
speaker must be 8
speaker must be 8
Ω
or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16
each speaker must be 16
Ω
or higher.
Center
The impedance must be 8
Ω
or higher.
Rear
MAIN A OR B: 4
MIN. /SPEAKER
A + B: 8
MIN. /SPEAKER
CENTER : 6
MIN. /SPEAKER
REAR : 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A + B:16
MIN. /SPEAKER
CENTER : 8
MIN. /SPEAKER
REAR : 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
Left
Right
Main
(Europe model)
Connecting the Power Supply Cords
After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if
you will not use this unit for a long period of time.
you will not use this unit for a long period of time.
■
AC OUTLET(S) (SWITCHED)
Europe model ............................................... 2 OUTLETS
U.K. model ..................................................... 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). These outlets
will supply power to any connected component whenever
this unit is turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is 100 W.
U.K. model ..................................................... 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). These outlets
will supply power to any connected component whenever
this unit is turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is 100 W.
To AC outlet
(Europe model)
MAIN A OR B: 4
MIN. /SPEAKER
A + B: 8
MIN. /SPEAKER
CENTER : 6
MIN. /SPEAKER
REAR : 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A + B:16
MIN. /SPEAKER
CENTER : 8
MIN. /SPEAKER
REAR : 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
SWITCHED
0104V1000RDS_19-23_EN
9/5/0, 4:41 PM
19