Land Pride rcf3696 Manuale Utente

37

Section 4: Operating Instructions

12/15/15

RCF3696, RCFM3696, RCF3610, & RCFM3610 Rotary Cutters 326-600M

Table of Contents

Section 4: Operating Instructions

Operating Checklist

Hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in the operation, transport, maintenance
and storage of the Rotary Cutter. Therefore, it is
absolutely essential that no one operates the cutter
without first having read, fully understood and become
totally familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:

•

Important Safety Information, pages 1 to 5

•

Section 1: Assembly & Set-Up, page 10

•

Section 3: Adjustments, page 31

•

Section 4: Operating Instructions, page 37

•

Section 5: Maintenance & Lubrication, page 43

Make sure the operator has completed the Operating
Checklist and Inspection below.

Safety Information

!

DANGER

Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.

!

DANGER

Do not operate a broken or bent driveline. Such drivelines can
break apart while rotating at high speeds causing serious
injury or death. Always remove Rotary Cutter from service
until damaged drivelines are repaired or replaced.

!

DANGER

Always disconnect driveline from tractor PTO shaft before
servicing underside of cutter. If tractor is started with PTO
engaged, the cutter can cause bodily injury or death.

Operating Checklist

✔

Check

Page

Read and follow all safety information carefully.
Refer to "Important Safety Information".

Make sure all guards and shields are in place.
Refer to "Important Safety Information".

Read and follow hook-up & preparation instructions.
Refer to "Section 1: Assembly & Set-Up".

Read and make all required adjustments.
Refer to "Section 3: Adjustments".

Read and follow all operating procedures.
Refer to "Section 4: Operating Instructions".

Read and follow all maintenance instructions.
Refer to "Section 5: Maintenance & Lubrication".

Make sure there are no hydraulic leaks on the unit.
Refer to "Avoid High Pressure Fluids Hazard".

Read and follow all lubrication Instructions.
Refer to "Lubrication".

Make sure all gearboxes are properly lubricated.
Refer to Gearbox lubrication.

Check cutter initially and periodically for loose bolts and
pins. Refer to “Torque Values Chart”.

Page 56

!

DANGER

Hydraulic fluid under high pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin or eyes, it must be
treated by a doctor familiar with this type of injury within a
few hours or gangrene may result. DO NOT DELAY.

!

DANGER

Be sure deck is lowered to the ground and all hydraulic
pressure is relieved before disconnecting or reconnecting
hydraulic line and/or fittings between Rotary Cutter and
tractor hydraulic system.

!

DANGER

Tractor PTO shield, gearbox shaft shield, and driveline
shields must be secured in place when operating cutter to
avoid injury or death from entanglement in driveline.

!

DANGER

All guards and shields must be installed and in good working
condition at all times during cutter operation.

!

DANGER

Never place hands or feet under the deck or attempt to make
adjustments to the cutter with PTO engaged. Cutter blades
rotating at high speeds cannot be seen and are located close
to the deck housing. Body extremities can be cut off instantly.

!

DANGER

Keep others away while cutter is operating. It can discharge
objects at high speeds. Therefor, the use of front and rear
safety guards is required when cutting along highways and in
areas where people may be present. Stop blade rotation if a
bystander is within several hundred feet.

!

DANGER

Always disengage PTO before lifting cutter up and never
operate cutter in the raised position. The cutter can discharge
objects at high speeds resulting in serious injury or death.

!

DANGER

Do not operate and/or travel across steep inclines where a
tractor can rollover resulting in serious injury or death.
Consult your tractor’s manual for acceptable inclines the
tractor is capable of traveling across.

!

DANGER

Do not use cutter as a fan. Cutting blades are not properly
designed or guarded for this use. Using cutter as a fan can
result in injury or death.