Impex TSA 5000 Manuale Utente
STEP 2 (See Diagram 2)
A.) Attach the right Front Vertical Frame (#3) to the right Base Frame (#1). Secure it
A.) Attach the right Front Vertical Frame (#3) to the right Base Frame (#1). Secure it
with two M10 x 3” Carriage Bolts (#76), one 5 1/8” x 2 ¾” Bracket (#34), two Ø ¾”
Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts
yet.
Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts
yet.
B.) Align a Ø 2 ½” Rubber Bumper (#59) to the hole on the Base Frame. Insert a Guide
Rod (#25) through the Rubber Bumper and into the Base Frame. Secure it with one
M10 x 1” Allen Bolt (#68) and Ø ¾” Washer (#66).
M10 x 1” Allen Bolt (#68) and Ø ¾” Washer (#66).
C.) Slide a Lower Safety Stop Frame (#92) onto the Guide Rod (#25). Attach a Safety
Hook (#93) to the Lower Safety Stop Frame. Secure it with one M10 x 1” Allen Bolt
(#68) and M10 Aircraft Nut (#86).
(#68) and M10 Aircraft Nut (#86).
D.) Slide a Safety Stop Frame (#26) onto the Guide Rod (#25).
E.) Attach the hole on top of the Right Vertical Frame (#5) to the top of the Guide Rod
E.) Attach the hole on top of the Right Vertical Frame (#5) to the top of the Guide Rod
(#25). Attach the top of Right Vertical Frame (#5) to the top of Front Vertical Frame
(#3). Attach the bottom of Right Vertical Frame (#5) to the Base Frame (#1).
(#3). Attach the bottom of Right Vertical Frame (#5) to the Base Frame (#1).
F.) Secure the Guide Rod (#25) to the Right Vertical Frame (#5) with one M10 x 1”
Allen Bolt (#68) and Ø ¾” Washer (#66). Secure the Right Vertical Frame (#5) to the
Base Frame with two M10 x 3” Carriage Bolts (#76), one 6 ¼” x 2” Bracket (#37),
two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts
and Bolts yet.
Base Frame with two M10 x 3” Carriage Bolts (#76), one 6 ¼” x 2” Bracket (#37),
two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts
and Bolts yet.
G.) Secure the Right Vertical Frame (#5) to the Front Vertical Beam (#3) with one
Triangle Bracket (#33), M10 x 3 1/8” Allen Bolt (#72), and
∅
3/4” Washer (#66) to the
top hole. Secure the bottom two holes with two M10 x 3 3/8” Carriage Bolts (#78),
∅
3/4” Washers (#66) and M10 Aircraft Nuts (#86).
H.) Repeat the above Procedures A, B, C, D, E, F and G to install the other side.
I.) Attach the Front Top Beam (#15) to the Front Vertical Beams (#3) and the Triangle
I.) Attach the Front Top Beam (#15) to the Front Vertical Beams (#3) and the Triangle
Brackets (#33). Align the Holes. Secure each end with two M10 x 3 3/8” Carriage
Bolts (#78), Ø3/4” Washers (#66), and M10 Aircraft Nuts (#86).
Bolts (#78), Ø3/4” Washers (#66), and M10 Aircraft Nuts (#86).
J.) Securely tighten all Nuts and Bolts previously installed.
7