Yamaha HTR-5760 Manuale Utente
71
English
TROUBLESHOOTING
ADDITIONAL
INFO
RMA
T
IO
N
N
Problem
Cause
Remedy
Refer to
page
The sound suddenly
goes off.
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
because of a short circuit, etc.
Check that the impedance selector setting is correct.
Check that the speaker wires are not touching each
other and then turn this unit back on.
other and then turn this unit back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE to cancel a mute.
Only the speaker on
one side can be
heard.
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
the cables may be defective.
Incorrect balance settings in SET MENU.
Adjust the SPEAKER LEVEL settings.
Only the center
speaker outputs
substantial sound.
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound from the
effect speakers.
effect speakers.
The sound field programs are turned off.
Press STRAIGHT (EFFECT) to turn them on.
You are using a source or program
combination that does not output sound
from all channels.
combination that does not output sound
from all channels.
Try another sound field program.
No sound from the
center speaker.
center speaker.
The output level of the center speaker is
set to minimum.
set to minimum.
Raise the level of the center speaker.
“CENTER SP” in SET MENU is set to
NONE.
NONE.
Select the appropriate setting for the center speaker.
One of the Hi-Fi DSP programs (except
for 7ch Stereo) has been selected.
for 7ch Stereo) has been selected.
Try another sound field program.
No sound from the
surround speakers.
surround speakers.
The output level of the surround speakers
is set to minimum.
is set to minimum.
Raise the output level of the surround speakers.
“SURR L/R SP” in SET MENU is set to
NONE.
NONE.
Select the appropriate setting for the surround left and
right speakers.
right speakers.
A monaural source is being played with
STRAIGHT.
STRAIGHT.
Press STRAIGHT (EFFECT) to turn on the sound
fields.
fields.
—
No sound from the
surround back
speakers.
surround back
speakers.
Presence speakers are selected.
Select surround back speakers in PR/SB SELECT.
“SURR L/R SP” in SET MENU is set to
NONE.
NONE.
If the surround left and right speakers are set to
NONE, the surround back speaker setting is
automatically set to NONE. Select the appropriate
setting for the surround speakers.
NONE, the surround back speaker setting is
automatically set to NONE. Select the appropriate
setting for the surround speakers.
“SURR B L/R SP” in SET MENU is set to
NONE.
NONE.
Select LRGx1 or SMLx1.
No sound from the
subwoofer.
subwoofer.
“LFE/BASS OUT” in SET MENU is set
to FRNT when a Dolby Digital or DTS
signal is being played.
to FRNT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
“LFE/BASS OUT” in SET MENU is set
to SWFR or FRNT when a 2-channel
source is being played.
to SWFR or FRNT when a 2-channel
source is being played.
Select BOTH.
The source does not contain low bass
signals.
signals.
00_HTR-5760_U_EN.book Page 71 Tuesday, February 17, 2004 10:47 AM