JVC HR-S9400U Manuale Utente
54
EN
Edit To Or
From Another
VCR
You can use your VCR as the player or the recorder.
MAKE CONNECTIONS
1
Connect an AV cable between the player’s VIDEO OUT
and AUDIO OUT connectors and the recorder’s VIDEO
IN and AUDIO IN connectors.
and AUDIO OUT connectors and the recorder’s VIDEO
IN and AUDIO IN connectors.
● If using another VCR with an S-VIDEO input or
output connector, it is recommended to use the S-
VIDEO connection to minimize picture degradation
while editing.
VIDEO connection to minimize picture degradation
while editing.
● When using your VCR as the recorder and a monaural
VCR as the player, connect the player’s AUDIO OUT
connector to the AUDIO IN L connector on the recorder.
connector to the AUDIO IN L connector on the recorder.
LOAD CASSETTES
2
Insert the playback cassette into the player and the
cassette to be recorded on into the recorder.
cassette to be recorded on into the recorder.
SET RECORDER’S INPUT
MODE
3
Set to AUX. With this VCR, press NUMBER key “0” (AU
appears on the front display panel in place of a channel
number).
appears on the front display panel in place of a channel
number).
NOTE:
When using this VCR as the recorder, be sure to select the
correct AUX input connector (depending on which input
connectors you use) at the Aux Input Screen. To select the
correct AUX input connector, follow steps 4, 9 – 11, 15
from the "Edit From A Camcorder" section,
correct AUX input connector (depending on which input
connectors you use) at the Aux Input Screen. To select the
correct AUX input connector, follow steps 4, 9 – 11, 15
from the "Edit From A Camcorder" section,
Z
pg. 52.
ENGAGE TAPE DUBBING
MODE
4
Follow steps 4, 9, 13 – 15 from the "Edit From A
Camcorder" section (
Camcorder" section (
Z
pg. 52)
START PLAYER
5
Set to its play mode.
NOTE:
If the player is equipped with a superimpose/OSD
disable feature then set "SUPERIMPOSE" to OFF before
pressing PLAY (
disable feature then set "SUPERIMPOSE" to OFF before
pressing PLAY (
Z
pg. 31).
START RECORDER
6
Set to its record mode.
NOTES:
● It is not possible to set both "TAPE DUB MODE" and "DYNAMIC
CONTRAST" to ON.
● Be sure to set "TAPE DUB MODE" back to "OFF" when you
finish editing.
● If you use a cable box or a DBS receiver connected to one of
the VCR's auxiliary input connectors and if you have used this
VCR as the recording deck for editing, be sure to select again
the required input at the AUX Input screen when you finish
editing.
VCR as the recording deck for editing, be sure to select again
the required input at the AUX Input screen when you finish
editing.
EDITING (cont.)
Your VCR
Player
Another VCR
VIDEO OUT
Audio/Video
cable
(supplied)
S-VIDEO IN
Recorder
AUDIO IN
VIDEO IN
AUDIO OUT
S-VIDEO OUT
S-Video
cable
(supplied)
Advantages Of S-VHS VCRs
You can edit from VHS to S-VHS, from S-VHS to VHS, or
from S-VHS to S-VHS.
from S-VHS to S-VHS.
● From VHS to S-VHS (VIDEO-VIDEO connection): Record
VHS playback signals in the S-VHS mode. Although the
picture quality is inherently limited by that of the original,
the edited tape has better picture quality than those made
by VHS-to-VHS editing.
picture quality is inherently limited by that of the original,
the edited tape has better picture quality than those made
by VHS-to-VHS editing.
● From S-VHS to VHS (VIDEO-VIDEO connection): Because
the picture quality of the source material is very high, the
edited tape has better picture quality than those made by
VHS-to-VHS editing.
edited tape has better picture quality than those made by
VHS-to-VHS editing.
● From S-VHS to S-VHS (S-VIDEO connection): All signals
will be transferred without degradation.