Funai 31B-254 Manuale Utente

13

EN

the timer is not programmed correctly, the incorrect timer 
setting stays in effect unless you cancel it. To cancel the 
incorrect timer setting, refer to “To Cancel or Check the Start/
End Time’’.

This function enables you to search and confirm the contents 
of the recorded programme(s) using the index mark.

• Use the remote control for this procedure.
• The tape must be fully rewound.
1) Press 

.

1) Press 

.

1) Press 

K

. The Quick-Find is cancelled.

This function will not operate in the Recording mode.

When you want to cancel the Quick-Find while in 
progress, press 

L

.

When the end of a tape is reached during the Quick-
Find, the tape will automatically rewind to the 
beginning. After rewinding finishes, the VCR will 
eject the tape and turn itself off.

• The index mark will be made automatically when 

 is pressed. It will also be marked at the starting 

point of Timer Recording and OTR.

• The index mark is not recorded if 

 

F

 is 

pressed and released during recording.

• The time gap between index marks on the tape should be 

greater than 1 minute for SP recording and 2 minutes for 
LP recording.

• Use the remote control for this procedure.
1) Press 

.

2) Press 

K

 or 

L

 repeatedly until the number of 

programmes that you want to skip appears.

3) Press 

s

 or 

B

. 

The VCR begins rewinding or fast forwarding to the 
beginning of desired programme.

When the preset programme is reached, the VCR will start 
playback automatically.

Index Search can be set up to 20.

This function will not operate in the Recording mode.

Operations must be followed up within 30 seconds 
from steps 

 to 

, otherwise the Index Search mode 

will be cancelled.

To exit the Index Search mode, press 

 in step 

 

or press 

L

 after step 

.

If a tape includes both programmes recorded in the PAL 
system and ones recorded in the NTSC system, this function 
may not be operated correctly.

• Use the remote control for this procedure.
1) Press 

twice.

2) Press 

K

 or 

L

 repeatedly until the desired 

time appears.

3) Press 

s

 or 

B

.

The VCR begins rewinding or fast forwarding to the 
specified point.

When 0:00 is reached, the VCR will start playback 
automatically.

Time Search can be set up to 9 hours 59 minutes 
(9:59).

This function will not operate in the Recording mode.

Operations must be followed up within 30 seconds 
from steps 

 to 

, otherwise the Time Search mode 

will be cancelled.

To exit the Time Search mode, press 

 in step 

 

or press 

L

 after step 

.

You can make copies of videotapes made by friends or relatives 
for your own enjoyment.

Connect the recording VCR (this unit), playing VCR (another 
VCR) and your TV as outline in the following diagram.

1) Insert a pre-recorded videocassette into the playing VCR.
2) Insert a blank videocassette, or one you want to record 

over, into the cassette compartment of the recording 
VCR.

3) Press 

 on the remote control to select the 

desired recording speed (SP/LP).

4) Select “AV2” position on the recording VCR. See “Other 

Connections”.

5) Press 

 on the recording VCR.

6) Begin playback of the tape in the playing VCR.
7) To stop recording, press 

 on the recording 

VCR, then stop playback of the tape in the playing VCR.

For best results during dubbing, use the VCR’s front 
panel controls whenever possible. The remote control 
might affect the playback VCR’s operation.

If video or colour fades in and out, you may be 
copying a copy guarded video tape.

Turn on the TV and select the video channel on the TV.

RF OUT

AERIAL

AV2(DECODER)

AV1(TV)

to RF OUT

to aerial

socket

[Source (Playing) VCR <Monaural>]

(another VCR)

to 21-Pin

Scart socket

[TV set]

(Use for monitoring)

[Editing (Recording) VCR]

(this unit)

RF cable (supplied)

HM210BD(EN).fm  Page 13  Thursday, March 2, 2006  6:07 PM