Casio 5286 Manuale Utente

 

x

 To set the time using a time calibration signal
See “To get ready for a receive operation” (page E-16).

 

x

 To set the time manually
See “Confi guring Current Time and Date Settings Manually” (page E-28).

 

x

 For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic 
Timekeeping” (page E-14).

x Second Hand.

Is the 

x Second Hand moving smoothly at one-second intervals?

Is the 

x Second Hand moving at two-second 

intervals or is it stopped completely? 

Go to step 2.

The watch is charged. For details about 
charging, see “Charging the Watch” 
(page E-10).

Power is low. Charge the watch by placing it in a 
location where it is exposed to light. For details, 
see “Charging the Watch” (page E-10).

NO

YES

YES

NEXT

Use the procedure under “To confi gure Home City settings” (page E-24) to confi gure your Home City.

 

x

 Proper time calibration signal reception depends on correct Home City, time, and date settings in the 
Dual Time Mode. Make sure you confi gure these settings correctly.

 

While the crown is pulled out, rotate it rapidly three turns away from you (for 
forward movement) or towards you (for reverse movement). High-speed 
movement will continue even if you release the crown.

 

While HS1 high-speed movement is progress, again rotate the crown rapidly 
three turns in the same direction as the current HS1 movement (away from you 
for forward movement or towards you for reverse movement).

 

Rotate the crown in the direction that is opposite that of the current high-speed 
movement or press any button.

 

x

 Leaving the crown pulled out for more than two minutes (approximately 30 minutes in the case of hand 
home position adjustment) without performing any operation will automatically cause crown operations 
to become disabled. If this happens, press the crown back in, pull it out, and then start the operation 
over again.

The crown can be pulled out to one of two (click) positions. Never apply undue force when pulling out the 
crown.

 

x

 In order to ensure full water resistance and to prevent damage due to impact, make sure that the crown 
is normally pushed in fully when using the watch.

 

x

 When pulling out the crown, avoid using undue force, which creates the risk of personal injury to your 
fi ngers and fi ngernails, and of watch malfunction.

 

 

 High-speed Movement
When setting a time or when performing home position adjustment (page E-44), you can move the hands 
either forward or back at high speed. There are two high-speed levels: HS1 and HS2 (faster than HS1).

Operations are performed using the watch’s crown, and the three buttons 
indicated by the letters 

A, B and C in this manual.

Hand Functions
z 

z  Hour Hand

x 

x  Second Hand

c 

c  Minute Hand

v 

v  Hour Hand (24-hour)

b 

b  Small Minute Hand

n 

n  Small Hour Hand

m 

m  Small Hour Hand (24-hour)

, 

,  Lower Dial Hand

. 

.  Day Indicator
This User’s Guide uses numbers shown above to identify watch hands and 
indicators.

 

x

 The movement of the 

x Second Hand and c Minute Hand of this watch are coordinated. To change 

the 

c Minute Hand setting, you will need to move the x Second Hand.

 

x

 

. Day Indicator movement is also coordinated with z Hour Hand movement. To change the . Day 

Indicator setting, you will need to move the 

z Hour Hand.

+

@

*

>

B

5 6

Congratulations upon your selection of this CASIO watch.

 

x

 Note that the product illustrations in this manual are intended for reference only, and so the actual 
product may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5 hours. Because of 
this, the radio-controlled atomic timekeeping function will not display the correct time for Newfoundland, 
Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by 
you or any third party arising through the use of this product or its malfunction.

MA1301-EA