Casio 5268 Manuale Utente
1
Operation Guide 5268
MA1111-EA
Your watch may differ somewhat from the one shown in the illustration.
•
Minute hand
Hour hand
Second hand
Day
Crown
(Normal position)
First click
(Setting Day)
Second click
(Setting Time)
To set the time
When the second hand is at
1.
12 o’clock, pull out the crown
to the second click to stop it.
Set the hands by rotating the
2.
crown. Rotate the crown to
move the hands clockwise.
Move the minute hand four or
five minutes past the time you
want to set, and then back it
up to the proper setting.
Push the crown back in to
3.
the normal position to restart
timekeeping.
To set the day
Pull the crown out to the first click.
1.
Set the day by rotating the crown.
2.
Push the crown back in to the normal position.
3.
Avoid changing the date setting while the current time is between 9:00 p.m. and
•
3:00 a.m.
Using the Stopwatch
Stopwatch minute hand
Stopwatch 1/20 second hand
This hand rotates and
*
indicates the second count
during the first 30 seconds.
Stopwatch second hand
The stopwatch lets you measure elapsed time up to 59 minutes, 59.95 seconds.
To measure elapsed time
Press
1.
A
to start the stopwatch.
Press
2.
A
to stop the stopwatch.
You can resume the measurement operation by pressing
•
A
again.
The 1/20-second hand stops moving after the first 30 seconds, but timing
•
continues internally. The 1/20-second hand will move to the current timing
value when the stopwatch is stopped.
Check the elapsed time.
3.
The example below shows an elapsed time of two minutes, 24.15 seconds.
•
Stopwatch second hand
[24 seconds]
Stopwatch minute hand
[2 minutes]
Stopwatch 1/20 second hand
[.15]
Press
•
B
to reset the stopwatch.
This will enter the Timekeeping Mode.
Notes:
Do not try to perform stopwatch operations while the crown is pulled out either
•
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
If the starting positions of the stopwatch second hand and 1/20 second hand
•
become misaligned, use the following procedures to adjust the positions of the
hands so they point to 12 o’clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
Press
1.
B
to reset the stopwatch, and check the stopwatch second hand,
1/20 second hand, and minute hand. They all should be at 12 o’clock.
To adjust the hands, pull out the crown to the second click.
2.
Press
3.
A
to move the stopwatch second hand to 12 o’clock.
Holding down
•
A
will move the second hand at high speed, until you release
the button.
Press
4.
B
to move the stopwatch 1/20 second hand to 12 o’clock.
Holding down
•
B
will move the 1/20 second hand at high speed, until you
release the button.
After making the adjustments you want, push the crown back in to its normal
5.
position.
Press
6.
B
to reset the stopwatch minute hand.
Note that pulling the crown out also stops the timekeeping second hand. After
•
performing the above procedure, you should also adjust the timekeeping setting.
For a watch with an elapsed time bezel
■
Rotate the elapsed time bezel to align the
mark with the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Elapsed time bezel
Some water resistant models are equipped with a screw
•
lock crown.
With such models, you must unscrew the crown in the
•
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
Also note that such watches are not water resistant while
•
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
3 dials (timekeeping seconds, stopwatch minutes and 1/20 seconds), day
Stopwatch function: Measuring capacity: 59'59.95"
Measuring unit: 1/20 second
Measuring mode: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 3 years on type SR927W (assuming one stopwatch operation 60 min./day)