Casio SGW300H-1AV Manuale Utente

Operation Guide 3202

1

Congratulations upon your selection of this CASIO watch.

Applications
The built-in sensors of this watch measure barometric pressure, temperature and 
altitude. Measured values are then shown on the display. Such features make this 
watch useful when hiking, mountain climbing, or when engaging in other such outdoor 
activities.

•

 The measurement functions built into this watch are not intended for taking 

measurements that require professional or industrial precision. Values produced 
by this watch should be considered as reasonable representations only.

•

 Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any 

damage or loss suffered by you or any third party arising through the use of 
this product or its malfunction.

•

 Depending on the model of your watch, display text 

appears either as dark figures on a light background, or 
light figures on a dark background. All sample displays 
in this manual are shown using dark figures on a light 
background.

•

 Button operations are indicated using the letters shown 

in the illustration.

•

 Note that the product illustrations in this manual are 

intended for reference only, and so the actual product 
may appear somewhat different than depicted by an 
illustration.

Use the procedure under “To configure Home City settings” to configure your Home 
City and daylight saving time settings.

Important!
Proper World Time Mode data depend on correct Home City, time, and date settings 
in the Timekeeping Mode. Make sure you configure these settings correctly.

See “Configuring Current Time and Date Settings”.

Your watch has 7 “modes”. The mode you should select depends on what you want to do.

•

 View the current time and date in the Home City

•

 Configure Home City and daylight saving time (DST) settings

•

 Configure time and date settings 

Timekeeping Mode

View the barometric pressure and temperature at your 
current location

Barometer/Thermometer 
Mode

•

 View the altitude at your current location

•

 Determine the altitude differential between two locations 

(reference point and current location)

Altimeter Mode

View the current time in one of 48 cities (31 time zones) 
around the globe

World Time Mode

Use the stopwatch to measure elapsed time

Stopwatch Mode

Use the countdown timer

Countdown Timer Mode

Set an alarm time

Alarm Mode

MO1004-EB

•

 The illustration below shows which buttons you need to press to navigate between 

modes.

•

 In any mode (except when a setting screen, with flashing digits is on the display), 

press 

B to illuminate the display.

General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.

•

 The watch returns to the Timekeeping Mode automatically if you do not perform any 

button operation for two or three minutes in the Alarm Mode.

•

 The watch will return to the Timekeeping Mode automatically if you do not perform 

any operation for about one hour after entering the Barometer/Thermometer Mode.

•

 If you leave a setting screen with flashing digits on the display for two or three minutes 

without performing any operation, the watch exits the setting screen automatically.

Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing 
when you last exited the mode appears first.

Scrolling
The 

B and D buttons are used on the setting screen to scroll through data on the 

display. In most cases, holding down these buttons during a scroll operation scrolls 
through the data at high speed.

Use the Timekeeping Mode to set and view the current 
time and date.

•

 In the Timekeeping Mode, the graphic in the center of 

the display indicates the passage of seconds.

There are two Home City settings: actually selecting the Home City and selecting 
either standard time or daylight saving time (DST).

To configure Home City settings
1. In the Timekeeping Mode, hold down 

A until the 

currently selected city code (Home City) starts to flash. 
This is the city code setting screen.

•

 Before the city code starts to flash, the message 

SET Hold will appear on the display. Keep 

A 

depressed until SET Hold disappears and the city 
code starts to flash.

•

 The watch will exit the setting mode automatically if 

you do not perform any operation for about two or 
three minutes.

•

 For details about city codes, see the “City Code 

Table”.

2. Press 

D (East) and B (West) to select the city code 

you want to use as your Home City.

•

 Keep pressing 

D or B until the city code you want 

to select as your Home City appears on the display.

3. Press 

C to display the DST setting screen.

4. Press 

D to toggle between Daylight Saving Time (On) 

and Standard Time (OFF).

•

 Note that you cannot switch between standard 

time and daylight saving time (DST) while UTC is 
selected as your Home City.

5. After all the settings are the way you want, press 

A to return to the Timekeeping Mode.

•

 The DST indicator appears to indicate that Daylight Saving Time is turned on.

•

 After you specify a city code, the watch will use UTC* offsets in the World Time 

Mode to calculate the current time for other time zones based on the current 
time in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping.