Kenwood TK-3402U16P Dépliant
KEY ASSIGNMENT MODE
This transceiver allows you to reprogram the Side 1 and Side 2 keys with any of the functions listed in
the table below.
the table below.
* To use this function, the Repeater Mode must be activated by
Programming Software.
Programming Software.
To change the functions of the Side 1 and Side 2 keys:
[1] With the transceiver power OFF, press and hold
the Side 1 and Side 2 keys while turning the
transceiver power ON.
• Continue to hold the Side 1 and Side 2 keys
until the LED lights orange and the transceiver
announces “Setup”.
[2] Continue to press and hold the key to be
reprogrammed (either the Side 1 or Side 2 key),
while releasing the remaining key.
reprogrammed (either the Side 1 or Side 2 key),
while releasing the remaining key.
• The transceiver will announce “Table zero”.
• If you continue to hold both keys, or if you release
both keys, the operation will cancel in 5 seconds.
[3] Release the key.
[4] Press the Side 1 or Side 2 key to increment/
decrement the table number to select the new key
function.
[3] Release the key.
[4] Press the Side 1 or Side 2 key to increment/
decrement the table number to select the new key
function.
• A voice announcement will inform you of the
currently selected Table number.
[5] Press the PTT switch to save the setting.
• A beep will sound and the transceiver will
announce the new Table number.
[6] Turn the transceiver power OFF and then ON
again to activate the new settings.
[6] Turn the transceiver power OFF and then ON
again to activate the new settings.
Note: The transceiver will automatically return to normal operation
if no action is performed for 20 seconds.
if no action is performed for 20 seconds.
PROGRAMMABLE FUNCTIONS
■ Calling Alert
Calling alert tone helps alerting party members that you are calling. To make a call,
press the key programmed as Calling Alert.
• Release the key to end the tone, and press and hold PTT to transmit and speak into
the microphone.
press the key programmed as Calling Alert.
• Release the key to end the tone, and press and hold PTT to transmit and speak into
the microphone.
■ Key Lock
Press and hold this key for 1 second to lock/ unlock the transceiver keys. The following
keys/ functions can still be used when Key Lock is active: Calling Alert, Key Lock,
Monitor, Monitor Momentary, PTT, Squelch Off, Squelch Off Momentary, and
Volume.
• When the transceiver power is turned OFF and then ON again, the Key Lock function
will be cancelled.
keys/ functions can still be used when Key Lock is active: Calling Alert, Key Lock,
Monitor, Monitor Momentary, PTT, Squelch Off, Squelch Off Momentary, and
Volume.
• When the transceiver power is turned OFF and then ON again, the Key Lock function
will be cancelled.
■ Key Lock with Status Memory
This operates the same as Key Lock except that when the transceiver power is turned
OFF and then ON again, the keys remain locked. Without Status Memory, when the
transceiver power is turned OFF and then ON again, the Key Lock function will be
cancelled.
■ Monitor
OFF and then ON again, the keys remain locked. Without Status Memory, when the
transceiver power is turned OFF and then ON again, the Key Lock function will be
cancelled.
■ Monitor
Momentarily press this key to deactivate QT or DQT signaling. Press the key again to
return to normal operation.
■ Monitor Momentary
return to normal operation.
■ Monitor Momentary
Press and hold this key to deactivate QT or DQT signaling. Release the key to return to
normal operation.
normal operation.
■ Scan
Scan is useful for monitoring signals on the transceiver channels. When scanning, the
transceiver checks for a signal on each channel and only stops if a signal is present. If
the QT/DQT matches, the transceiver stops at the channel and opens the squelch so
you can listen to the call. If the QT/DQT does not match, the call is ignored and scanning
continues.
■ Scan + Temporary Delete (Side 2 key default)
transceiver checks for a signal on each channel and only stops if a signal is present. If
the QT/DQT matches, the transceiver stops at the channel and opens the squelch so
you can listen to the call. If the QT/DQT does not match, the call is ignored and scanning
continues.
■ Scan + Temporary Delete (Side 2 key default)
Press this key to start scanning the transceiver channels. When Scan pauses at an
undesired channel, you can remove that channel from the scanning sequence by
pressing and holding this key for 3 seconds.
■ Scrambler
undesired channel, you can remove that channel from the scanning sequence by
pressing and holding this key for 3 seconds.
■ Scrambler
Press this key to activate (a single beep sounds) and deactivate (a double beep sounds)
the scrambler function of the selected channel. The Scrambler function allows you to
hold a conversation in complete privacy. When the Scrambler function is activated, any
other party that is listening to your channel will be unable to understand your
conversation.
■ Squelch Off
the scrambler function of the selected channel. The Scrambler function allows you to
hold a conversation in complete privacy. When the Scrambler function is activated, any
other party that is listening to your channel will be unable to understand your
conversation.
■ Squelch Off
Press this key to hear background noise. Press the key again to return to normal
operation.
■ Squelch Off Momentary
operation.
■ Squelch Off Momentary
Press and hold this key to hear background noise. Release the key to return to normal
operation.
■ Super Lock (Side 1 key default)
operation.
■ Super Lock (Side 1 key default)
Super Lock locks the same keys as Key Lock. Press and hold this key for 4 seconds to
lock the transceiver keys. To deactivate Super Lock, with the transceiver power OFF,
press and hold the Side 2 key for 2 seconds while turning the transceiver power ON.
• When the LED lights orange, release the Side 2 key. A confirmation tone will sound.
■ Low Transmit Power
lock the transceiver keys. To deactivate Super Lock, with the transceiver power OFF,
press and hold the Side 2 key for 2 seconds while turning the transceiver power ON.
• When the LED lights orange, release the Side 2 key. A confirmation tone will sound.
■ Low Transmit Power
Press this key to change the transmit power to low power. Each time you press this key,
the transmit power toggles between high and low.
the transmit power toggles between high and low.
ALL RESET MODE
At some point in time, you may desire to reset the transceiver settings to their
default values. This function will reset all channels to their default frequencies and
QT/DQT, the VOX function to its default status, and all keys to their default
functions.
default values. This function will reset all channels to their default frequencies and
QT/DQT, the VOX function to its default status, and all keys to their default
functions.
To reset the transceiver:
[1] With the transceiver power OFF, press and hold
the PTT switch, the Side 1 key, and the Side 2 key
while turning the transceiver power ON.
[1] With the transceiver power OFF, press and hold
the PTT switch, the Side 1 key, and the Side 2 key
while turning the transceiver power ON.
• Continue to hold the keys for 2 seconds, until
the LED lights orange.
[2] Release the keys.
[2] Release the keys.
• The keys must be released within 1 second after the
LED lights orange, otherwise All Reset Mode will cancel.
• The transceiver announces “Confirm” and returns to
normal operation.
TROUBLESHOOTING GUIDE
Problem
Solution
Cannot Turn the
transceiver power
ON.
transceiver power
ON.
The battery pack may be dead. Recharge or replace the
battery pack.
The battery pack may not be installed correctly.
Remove the battery pack and install again.
battery pack.
The battery pack may not be installed correctly.
Remove the battery pack and install again.
Battery power
dies shortly after
charging
dies shortly after
charging
The battery pack life is finished. Replace the battery
pack with a new one.
pack with a new one.
Cannot talk to or
hear other
members in your
group.
hear other
members in your
group.
Make sure you are using the same frequency and
QT/DQT settings as the other members in your group.
Other group members may be using the Scrambler
function. Turn on your transceiver
’s Scrambler.
Other group members may be too far away. Make sure
you are within range of the other transceivers.
Other voices
(besides group
members
(besides group
members
’) are
present on the
channel.
channel.
Change the QT/DQT settings.
Make sure all group members change the settings on
their transceivers to match the new QT/DQT setting.
Make sure all group members change the settings on
their transceivers to match the new QT/DQT setting.
Table
Number
Function Name
0
None (no function)
1
Calling Alert
2
Key Lock
3
Key Lock with Status Memory
4
Monitor
5
Monitor Momentary
6
Scan
7
Scan + Temporary Delete (Side 2 key default)
8
Scrambler
9
Squelch Off
10
Squelch Off Momentary
11
Super Lock (Side 1 key default)
12
Low Transmit Power
13
RX/TX Frequency Scan*