Sony DCR-HC30/HC40 Manuale Utente
Du
b
b
b
in
g
/E
d
itin
g
g
Dubbing/Editing
99
To set the [IR SETUP] code
When you connect with an A/V connecting
cable, you need to check the [IR SETUP] code
signal to see if your VCR can be operated by
your camcorder (infrared ray emitter).
cable, you need to check the [IR SETUP] code
signal to see if your VCR can be operated by
your camcorder (infrared ray emitter).
1
Touch
, then [IR SETUP].
2
Select the [IR SETUP] code of your VCR
with
with
/
, then touch
.
For the [IR SETUP] code of your VCR,
refer to “[IR SETUP] code list” (p. 99).
When there is more than one code listed for
the manufacturer of your VCR, try each
code and find the most appropriate one.
refer to “[IR SETUP] code list” (p. 99).
When there is more than one code listed for
the manufacturer of your VCR, try each
code and find the most appropriate one.
3
Touch
[PAUSEMODE].
4
Select the mode to cancel recording
pause on the VCR, then touch
pause on the VCR, then touch
.
Refer to the operating instructions supplied
with your VCR for details on operation.
with your VCR for details on operation.
5
Point the infrared ray emitter of your
camcorder towards the remote sensor on
your VCR, from about 30 cm (12 in.)
away, with no obstructions.
camcorder towards the remote sensor on
your VCR, from about 30 cm (12 in.)
away, with no obstructions.
6
Insert a cassette into your VCR, and set
the VCR to recording pause.
the VCR to recording pause.
7
Touch [IR TEST].
8
Touch [EXEC].
The recording starts on your VCR when the
setting is correct. [Completed.] appears
when the [IR SETUP] code test is finished.
Go on to “Step 2 : Adjusting the
synchronization of the VCR” (p. 100).
When recording fails to start, select another
[IR SETUP] code and try again.
The recording starts on your VCR when the
setting is correct. [Completed.] appears
when the [IR SETUP] code test is finished.
Go on to “Step 2 : Adjusting the
synchronization of the VCR” (p. 100).
When recording fails to start, select another
[IR SETUP] code and try again.
[IR SETUP] code list
The following [IR SETUP] codes are recorded
on your camcorder by default. (It is set at “3” as
the default setting.)
on your camcorder by default. (It is set at “3” as
the default setting.)
Infrared ray emitter
VCR
Remote sensor
Manufacturing
company
company
[IR SETUP] code
Sony
1, 2, 3, 4, 5, 6
Admiral (M. Wards)
89
Aiwa
47, 54, 80
Akai
49, 51
Audio Dynamic
21, 35
Bell&Howell (M. Wards) 36
Broksonic
21, 70, 82
Canon
77, 78
Citizen
47
Craig
47, 73
Curtis Mathis
8, 77, 80
Daewoo
26, 40, 77
DBX
21, 33, 35
Dimensia
8
Emerson
26, 48, 59, 70, 80, 81, 82
Fisher
36, 37, 44, 45
Funai
80
General Electric
8, 32*, 77, 94*, 101
Goldstar/LG
47
GO VIDEO
71
Hitachi
8, 42, 78
HQ
40
Instant Replay
77, 78
JC Penny
8, 21, 33, 35, 36, 42, 77
JVC
12, 13, 14, 21, 33, 35
Kenwood
21, 33, 35, 47
LXI (Sears)
36, 37, 42, 44, 45, 47,
49, 80
49, 80
Magnavox
17, 77, 78, 83
Marantz
21, 33, 35
Marta
47
Memorex
37, 77
Minolta
8, 42
Mitsubishi/MGA
22, 23, 24, 28, 29
,
continued