Sony 930 Manuale Utente
7
Chapter 7 Location and Function of Parts and Controls
102
HDC-900/950/930 Series Product Information Manual
7-5.
CNU-700, Camera Command Network Unit
7-5-1
Front and Rear Panels
a
POWER switch and indicator
Press to turn the power ON or OFF. The indicator
illuminates when power is switched on.
illuminates when power is switched on.
b
CCU (camera control unit) 1 through 6
connectors (8-pin)
connectors (8-pin)
Connect to the RCP/CNU REMOTE connector on a
CCU-700A/700AP Camera Control Unit using a CCA-5
cable.
CCU-700A/700AP Camera Control Unit using a CCA-5
cable.
c
RCP (remote control panel) 1 through 6
connectors (8-pin)
connectors (8-pin)
Connect to the CCU/CNU REMOTE connectors on an
RCP-700 Series Remote Control Panel using a CCA-5
cable.
RCP-700 Series Remote Control Panel using a CCA-5
cable.
d
MSU (Master Set-up Unit) connector (8-pin)
Connect to the CCU/CNU REMOTE connector on an
MSU-700 Master Set-up Unit using a CCA-5 cable.
MSU-700 Master Set-up Unit using a CCA-5 cable.
e
VCS (video selector) connector (8-pin)
Connect to the REMOTE connector of a VCS-700
Video Selector using a CCA-5 cable.
Video Selector using a CCA-5 cable.
f
AUX1 and AUX2 (auxiliary 1 and 2) connectors
(8-pin)
(8-pin)
Connect to the AUX1 or AUX2 connector of another
CNU-700 using a CCA-5 cable when controlling
multiple cameras with two or more CNU-700 units. You
can connect up to eight CNU-700 units.
CNU-700 using a CCA-5 cable when controlling
multiple cameras with two or more CNU-700 units. You
can connect up to eight CNU-700 units.
g
CHARACTER 1and 2 connectors (BNC type)
Supply character data as a 525 or 625-line, black-and-
white video signal. The signal output is automatically
selected according to the reference signal input to the
REFERENCE connector. If no reference signal is input,
the CNU-700 for the USA and Canada supplies a 525-
line video signal, the CNU-700 for other countries
supplies a 625-line video signal. You can select
whether to add a sync signal to the output signal with
switch S7 (SYNC ON/OFF) on the AT board. Refer to
the system manual for details on the board switch
settings.
white video signal. The signal output is automatically
selected according to the reference signal input to the
REFERENCE connector. If no reference signal is input,
the CNU-700 for the USA and Canada supplies a 525-
line video signal, the CNU-700 for other countries
supplies a 625-line video signal. You can select
whether to add a sync signal to the output signal with
switch S7 (SYNC ON/OFF) on the AT board. Refer to
the system manual for details on the board switch
settings.
h
REFERENCE (reference signal input) loop
connectors (BNC type)
connectors (BNC type)
Accepts a reference signal (VS, BS, etc.). The signal
output from the CHARACTER connector is
synchronized with the input signal.
output from the CHARACTER connector is
synchronized with the input signal.
i
RS-232C 1 through 3 connectors (D-sub 9-pin)
Used for RS-232C interfaces. The function of these
connectors depends on whether or not an optional
BKP-7930 System Expansion Board is installed in the
CNU-700 as shown below.
connectors depends on whether or not an optional
BKP-7930 System Expansion Board is installed in the
CNU-700 as shown below.
POWER
CAMERACOMMAND NETWORK UNIT
7
8
9
10
11
12
CCU
1
2
3
4
5
6
RCP
1
2
3
4
5
6
7
8
9
10
11
12
CCU
MSU
VCS
AUX1
AUX2
AUX4
~AC IN
MSC
VCS
AUX3
1
POWER switch and indicator
Front panel
3
RCP 1 through 6 connectors
2
CCU 1 through 6 connectors
Rear panel
4
MSU connector
5
VCS connector
6
AUX1 and AUX2 connectors
qa
Optional board
insertion section
q;
-AC IN connector
9
RS-232C 1 through 3 connectors
8
REFERENCE connectors
7
CHARACTER 1 and 2 connectors
Connector
No
No BKP-7930
installed
With BKP-7930
installed
1
Reserved for ISR system
2
Reserved for RS-232C interface
3
Not used
Reserved for RS-232C
system