Magellan MG-6060 Manuale Utente

Section [201]

Performing a software reset will reset all programmed sections 
back to the factory defaults. To perform a software reset:

1.

Access the installer programming mode (page 11).

2.

Enter section [201].

Section [180]: 000 = Disabled; 147 = Lock Enabled; 

Default = Disabled

Program 147 into section [180] to lock all programming. 
Performing a hardware reset will not affect the current console 
settings. To remove the Installer Lock, enter 000.

Section [090]: Option [5]
Option [5] OFF = Console Tamper Supervision disabled 

(default)

Option [5] ON =

Console Tamper Supervision enabled

Magellan can be programmed to monitor its on-board tamper 
status. The console will follow its programmed tamper 
recognition options. Refer to Tamper Recognition Options on 
page 22 for more information.

Section [090]: Option [2]
Option [2] OFF = Console beep on trouble disabled (default)
Option [2] ON =

Console beep on trouble enabled

When enabled, the console emits an intermittent beep tone 
whenever a trouble condition occurs in the system. The 
intermittent beep tone remains activated until the user enters the 
Trouble Display by pressing the left [

] key (

). The 

intermittent beeps will re-initialize whenever a new trouble 
occurs or the trouble restores and re-occurs.

Section [093]: Option [8]
Option [8] OFF = FM tuner is disabled when the system is 

armed (default)

Option [8] ON =

FM tuner is enabled when system is armed

With section [093] option [8] ON, the Magellan’s radio is turned 
ON automatically after the system is armed (after the Exit Delay 
timer has elapsed).

Section [096]: Option [5]
Option [5] OFF = Daylight savings time disabled (default)
Option [5] ON =

Daylight savings time enabled

With section [096] option [5] ON, Magellan adjusts the system’s 
clock (time) for daylight saving changes. At 2:00AM on the first 
Sunday of a full weekend in April, the console will add one hour 
to the programmed time (clock). At 2:00 AM on the last Sunday 
of a full weekend in October, the console will subtract one hour 
from the programmed time.

Section [096]: Option [6]
Option [6] OFF = AC power failure warning disabled (default)
Option [6] ON =

AC power failure warning enabled

With this feature enabled, the console emits an intermittent beep 
tone whenever an AC power failure is detected. The intermittent 
beep tone remains activated until the user enters the Trouble 
Display by pressing the left [

] key (i). The intermittent 

beeps will re-initialize whenever the trouble occurs or the trouble 
restores and re-occurs.

When the system experiences problems or is tampered with, the 

Information symbol ( ) will appear on the LCD screen and the 

 

light will illuminate. The potential troubles that the Magellan 
system can experience are listed below. To access the Trouble 
Display:

1.

Press the   key.

2.

Use the [

] key to scroll through the displayed troubles.

3.

Press the [

] key to view details on the desired trouble.

Bypass

There is a zone (or zones) that is bypassed in 
the system.

Alarm Memory

An alarm has occurred in the system. The 
zones displayed went into alarm.

Console Low Bat

The backup battery pack is disconnected, 
needs to be recharged or replaced.

Doorbell Low Bat

Wireless transmitter being used as a doorbell 
(page 17) requires its batteries changed.

Zone Low Battery

Zone(s) displayed indicate where a wireless 
transmitter’s battery needs to be replaced.

Clock Loss

The time and date were reset to default. To 
reprogram:
1. Press the 

 key.

2. Press the [3] key.
3. Press the 

 key to display the time 

using the 12-hour clock or the 

 key 

to display the time using the 24-hour clock.

4. Enter the desired time and then press 

.

5. Enter the date and then press 

.