Hamilton Beach MCRES-525 Dépliant
P
ARTS LIST
– B
ARBED ADAPTERS ARE SOLD SEPARATELY
Parts
QTY
PARTS
QTY
MCRES-525™ Reservoir
1
Retention screws
4
Fill-cap & o-ring
1
Port plug
1
This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in
damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their
installation. The following instructions are subject to change without notice. Please visit our web site at
updates.
The MCRES-525™ reservoir is designed to be installed in a 5 ¼” drive bay. It features three 3/8” threaded ports (standard NPT thread)
to accommodate a number of configurations (see * Swiftech fittings). The port usage is defined as follows:
The MCRES-525™ reservoir is designed to be installed in a 5 ¼” drive bay. It features three 3/8” threaded ports (standard NPT thread)
to accommodate a number of configurations (see * Swiftech fittings). The port usage is defined as follows:
(1) Discharge port located at the “stepped-down” compartment. This port must ALWAYS be connected to the
pump inlet for the MCRES-525™ to operate properly.
pump inlet for the MCRES-525™ to operate properly.
(2) Inlet ports can be used interchangeably: in “single inlet” configuration (the most common), or “dual inlet”
configuration when devices are returning to the reservoir in parallel. One port plug is provided to seal one of the
inlets in order to accommodate the most common “single inlet” configuration.
configuration when devices are returning to the reservoir in parallel. One port plug is provided to seal one of the
inlets in order to accommodate the most common “single inlet” configuration.
Installation of the fittings requires sealant. Recommended sealants include Teflon pipe dope or solvent cement
(Goop), which are the easiest to use; Teflon tape will require three to four turns for a good seal. Tighten fittings
until firm, do not make up to the nut interfering with the threaded hub - a thread should be visible on the fitting. Use
of silicone sealants is not recommended.
(Goop), which are the easiest to use; Teflon tape will require three to four turns for a good seal. Tighten fittings
until firm, do not make up to the nut interfering with the threaded hub - a thread should be visible on the fitting. Use
of silicone sealants is not recommended.
The following guide assumes that all liquid cooling components in your system, such as radiator, pump, and water-block(s) have been
already installed, and the graphic below shows an overview of a typical installation.
Swiftech Fittings & Spare parts
Important!
All fittings (except DP-11) require sealant: plumbers tape, or plumbers goop (preferred)
A6-8
A6-6
PI011623S
DP-11
P6N
1/2" barb to 3/8" NPT, for 1/2"
Inner diameter tubing (3/4" or
5/8" outer diameter) – Order
Separately
3/8" barb to 3/8" NPT, for
3/8" Inner diameter tubing
(1/2"outer diameter) – Order
separately
3/8” NPT to ½” tube (outer
diameter) quick-connect
fitting – Order separately
Fill-cap & o-ring
Included
3/8” NPT Port
plug
Included
Copyright Swiftech 2004 – All rights reserved – Last revision date: 1-25-05
Rouchon Industries, Inc., dba Swiftech – 1703 E. 28
Rouchon Industries, Inc., dba Swiftech – 1703 E. 28
th
Street, Signal Hill, CA 90755 – Tel. 562-595-8009 – Fax 562-595-8769 - E Mail:
Swiftech@swiftnets.com – URL:
http://www.swiftnets.com
- Information subject to change without notice