Chamberlain 3265CM Manuale Utente
To Open the Door Manually
The door should be fully closed if
possible. Pull down on the
emergency release handle and lift
the door manually. To reconnect
the door to the opener, press the
door control push bar.
possible. Pull down on the
emergency release handle and lift
the door manually. To reconnect
the door to the opener, press the
door control push bar.
The lockout feature prevents the
trolley from reconnecting
automatically. Pull the emergency
release handle down and back
(toward the opener). The door can
then be raised and lowered
manually as often as necessary.
To disengage the lockout feature,
pull the handle straight down. The
trolley will reconnect on the next
UP or DOWN operation, either
manually or by using the door
control or remote.
trolley from reconnecting
automatically. Pull the emergency
release handle down and back
(toward the opener). The door can
then be raised and lowered
manually as often as necessary.
To disengage the lockout feature,
pull the handle straight down. The
trolley will reconnect on the next
UP or DOWN operation, either
manually or by using the door
control or remote.
To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage
garage door:
• If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage doorway
is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
27
Trolley
Release
Arm
Release
Arm
NOTIC
E
Emergency
Release
Handle
(Pull Down)
Release
Handle
(Pull Down)
Trolley
Release
Arm
Release
Arm
NOTICE
Emergency
Release Handle
(Down and Back)
Release Handle
(Down and Back)
LOCKOUT POSITION
MANUAL DISCONNECT
POSITION
Using the Wall-Mounted
Door Control
Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close
the door. Press again to reverse the door
during the closing cycle or to stop the
door while it's opening.
the door. Press again to reverse the door
during the closing cycle or to stop the
door while it's opening.
Light feature
Press the Light button to turn the opener
light on or off. It will not control the opener lights when the
door is in motion. If you turn it on and then activate the
opener, the light will remain on for 4-1/2 minutes. Press
again to turn it off sooner. The 4-1/2 minute interval can be
changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press
and hold the Lock button until the light blinks (about 10
seconds). A single blink indicates that the timer is reset to
1-1/2 minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
light on or off. It will not control the opener lights when the
door is in motion. If you turn it on and then activate the
opener, the light will remain on for 4-1/2 minutes. Press
again to turn it off sooner. The 4-1/2 minute interval can be
changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press
and hold the Lock button until the light blinks (about 10
seconds). A single blink indicates that the timer is reset to
1-1/2 minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close
from the Door Control, the Outside Keylock and the
Keyless Entry Accessories.
remote controls. However, the door will open and close
from the Door Control, the Outside Keylock and the
Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The push bar light will flash as long as the Lock feature
is on.
The push bar light will flash as long as the Lock feature
is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The Lock
feature will also turn off whenever the “learn” button on the
motor unit panel is activated.
2 seconds.The push bar light will stop flashing. The Lock
feature will also turn off whenever the “learn” button on the
motor unit panel is activated.
Additional features when used with the 3-Button
hand-held remote
hand-held remote
A) To control the opener lights:
In addition to operating the door, you may
program the remote to operate the lights.
program the remote to operate the lights.
1. With the door closed, press and hold a small remote
button that you want to control the light.
2. Press and hold the Light button on the Multi-Function
door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights flash, release all buttons.
LOCK
LIGHT
Push
Button
Button
Lock
Button
Button
Light
Button
Button
B) To operate one door using all three buttons on the
hand-held remote:
You may program the remote to
openthe door with the large button,
close it with the middle button, and
stop the door’s movement with the
third button.
openthe door with the large button,
close it with the middle button, and
stop the door’s movement with the
third button.
NOTE: If remote is already programmed, you must first
erase all codes. See Programming.
erase all codes. See Programming.
1. With the door closed, press and hold the large remote
push button.
2. Press and hold the Lock button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Open
Close
Stop