Marley Engineered Products PH4AB Manuale Utente
MODEL NO.
PH4AB
Portable Unit Heater
WARNING
Installation & Maintenance Instructions
Dear Owner,
Congratulations!
Thank you for purchasing this new heater manufactured by Marley Engineered
Products. You have made a wise investment selecting the highest quality product in the heating indus-
try. Please carefully read the installation and maintenance directions shown in this manual. You should
enjoy years of efficient heating comfort with this product from Marley Engineered Products... the indus-
try’s leader in design, manufacturing, quality and service.
try. Please carefully read the installation and maintenance directions shown in this manual. You should
enjoy years of efficient heating comfort with this product from Marley Engineered Products... the indus-
try’s leader in design, manufacturing, quality and service.
... The Employees of
Marley Engineered Products
Marley Engineered Products
Read Carefully -
These instructions contain vital infor-
mation for the proper installation, use and efficient opera-
tion of the heater. Carefully read these instructions before
installation, operation, or cleaning of the heater. Failure to
adhere to the instructions could result in fire, electric
shock, serious personal injury, death or property damage.
Save these instructions and review frequently for continu-
ing safe operation and instruction future users.
tion of the heater. Carefully read these instructions before
installation, operation, or cleaning of the heater. Failure to
adhere to the instructions could result in fire, electric
shock, serious personal injury, death or property damage.
Save these instructions and review frequently for continu-
ing safe operation and instruction future users.
1.
Connect to properly grounded outlets only.
2.
Check heater voltage and amperage on back of heater to
make sure it agrees with the electric service supplied.
3.
Ground fault circuit protection is required if heater is used in
damp areas such as basements or garages. This is not suit-
able for use in wet or very humid locations.
able for use in wet or very humid locations.
4.
Do not use outdoors.
5.
Never locate heater where it may fall into a bathtub or other
water container.
6.
Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock, fire,
or damage the heater.
or damage the heater.
7.
To prevent a possible fire, do not block air intakes or exhaust
in any manner. Do not use soft surfaces, like a bed, where
openings may become blocked. Clean as often as neces-
sary to prevent dust from clogging the grilles or element fins.
Keep all electrical cords, drapes, paper, plastics and other
combustibles away from heater.
openings may become blocked. Clean as often as neces-
sary to prevent dust from clogging the grilles or element fins.
Keep all electrical cords, drapes, paper, plastics and other
combustibles away from heater.
8.
Do not run cord under carpeting. Do not cover cord with
throw rugs, runners, etc. To prevent entanglement or damage,
route cord away from high traffic areas.
route cord away from high traffic areas.
9.
A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids are
repaired by a reputable repair service.
repaired by a reputable repair service.
10. If this heater or its power cord become damaged or malfunc-
tion in any way, unplug heater, discontinue use, and have
unit repaired by a reputable repair service.
unit repaired by a reputable repair service.
11. Do not operate heater without stand.
12. Do not use an extension cord with this heater. Do not cut off
12. Do not use an extension cord with this heater. Do not cut off
plug and wire heater directly.
13. When heater is to be wall or ceiling mounted, the anchoring
provisions must be of sufficient strength to support the total
weight of the heater plus the weight of the mounting provi-
sions. Failure to properly secure the supporting members of
the building structure could allow the heater to fall.
weight of the heater plus the weight of the mounting provi-
sions. Failure to properly secure the supporting members of
the building structure could allow the heater to fall.
!
SAVE THESE INSTRUCTIONS
1
FILE #E21609