Fedders A6V05S2B Manuale Utente
3
WINDOW INSTALLATON
INSTALLATION
Tools Needed
Screwdrivers
Tape Measure
Carpenter’s Level
Knife
Drill
Window Requirements:
Your new room air conditioner is factory prepared for easy installation
in a horizontal sliding or casement type window with a minimum width
of 15 1/2 inches. Unit will fit a 42 inch high window opening as
received from factory.
Your new room air conditioner is factory prepared for easy installation
in a horizontal sliding or casement type window with a minimum width
of 15 1/2 inches. Unit will fit a 42 inch high window opening as
received from factory.
Use caution when working around exposed sharp edges
of the cabinet and sharp coils to avoid injury or torn
clothing.
of the cabinet and sharp coils to avoid injury or torn
clothing.
Make sure unit is unplugged before removing the
decorative front.
decorative front.
It is recommended that you have help to install your unit
and that you use proper lifting technique to avoid
personal injury.
and that you use proper lifting technique to avoid
personal injury.
A
B
C
D
E
Support Platform
7/16” mach. screws
3/8” Self tapping screws
Sill plate
7/16” mach. screws
3/8” Self tapping screws
Sill plate
Support Angle
Leveling Bolt
Leveling Bolt
A
B
C
D
E
F
F
A
A
B
C
D
E
1” long screws
Support Platform
Lower window track
Support Platform
Lower window track
Window Sill
Shim Strip
Shim Strip
A
B
C
D
E
Before you start:
Sliding Window Installation
Make sure unit is unplugged before removing chassis
from cabinet.
from cabinet.
1.
Choose the installation site. It is imperative that window frame
assembly and side of structure are adequate to support weight of
assembly and side of structure are adequate to support weight of
unit. Reinforce if necessary.
2. Slide open one window sash to install support platform.
3. Attach support platform to sill plate with three (3) 3/8” long self-
tapping screws (Fig. 3).
4. Loosely attach support angle to bottom of support platform using
two (2) 7/16” long machine screws, flat washers, and nuts.
5. Place support platform against lower window track and firmly
against vertical edge of window frame (Fig. 4).
6. Attach support platform to window sill using two (2) 1” long
self-tapping screws (Fig. 4).
If required, overcome interference of support platform with
window track or storm windows by securely attaching a shim
strip to the window sill. Strip should be as long as width of
support platform and flush with back edge of sill. Thickness of
strip should be controlled by amount of interference.
window track or storm windows by securely attaching a shim
strip to the window sill. Strip should be as long as width of
support platform and flush with back edge of sill. Thickness of
strip should be controlled by amount of interference.
7. Pull support angle against outside of structure. Tighten two (2)
7/16” long machine screws on top of support platform (Fig. 3).
8. Adjust leveling bolt to position support angle in a level plane.
This will allow for proper angle. Tighten leveling bolt locknut
(Fig. 3).
(Fig. 3).
Important: Unit must be level or tilted back slightly to facilitate proper
condensate disposal.
condensate disposal.
Fig. 4
Fig. 3
1” long wood screws
2
3/8” Self tapping screws
7
7/16” mach. screws/nuts
2
Leveling Bolt/ Nut
1
Speed Clips
2
A
B
C
D
E
A
B
C
D
E
Installation Parts Kit
Fastener Identification
Fastener Identification
Description
Quantity
SUPPORT PLATFORM ASSEMBLY
The installation is intended to be permanent, and when installed in
apartment or rental properties, permission to make modifications
should be obtained from owners or landlords of buildings prior to
installation of unit.
apartment or rental properties, permission to make modifications
should be obtained from owners or landlords of buildings prior to
installation of unit.