Regency F37-NG Manuale Utente
12
F37 Regency
®
Rear Flued Room Sealed Freestanding Gas Heater
System Data - F37
Burner Inlet Orifi ce Sizes:
NG LPG
Burner
NG LPG
Burner
#37
#52
Max. Input Rating
31.7 mj
Min. Input Rating
16 mj
Supply Pressure
NG
min.
1.13kPa
LPG
min.
2.75kPa
Manifold Pressure
NG
NG
.89
kPa
LPG
2.55
kPa
GAS CONNECTION
The gas connection is a 1/2" NPT Male
Thread. Copper can be used or other con-
nections approved by AG 604.
Thread. Copper can be used or other con-
nections approved by AG 604.
When using copper or fl ex connectors use only
approved fi ttings. Always provide a union so
that gas lines can be easily disconnected for
burner and/or valve servicing. Flare nuts for
copper lines are usually considered to meet
this requirement.
approved fi ttings. Always provide a union so
that gas lines can be easily disconnected for
burner and/or valve servicing. Flare nuts for
copper lines are usually considered to meet
this requirement.
Important: Always check for gas leaks with a
soap and water solution or gas leak detector.
Do not use open fl ame for leak testing.
soap and water solution or gas leak detector.
Do not use open fl ame for leak testing.
Note: Prior to any pressure testing of
the gas supply piping system
that exceeds test pressures of
3.45 kPa, this appliance must
be disconnected from the pip-
ing system. If test pressures
equal to or less than 3.45 kPa
are used then this appliance
must be isolated from the piping
system by closing its individual
manual shut-off valve during the
testing.
that exceeds test pressures of
3.45 kPa, this appliance must
be disconnected from the pip-
ing system. If test pressures
equal to or less than 3.45 kPa
are used then this appliance
must be isolated from the piping
system by closing its individual
manual shut-off valve during the
testing.
VERTICAL TERMINATION WITH
CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING
A SEPARATE SOLID FUEL BURNING APPLIANCE.
This appliance is designed to be attached to two 3" (76mm) co-linear aluminium fl ex running the
full length of the chimney. See the Flueing Arrangements chart in the "Flue Arrangement" sec-
tion for minimum and maximum fl ue lengths. See chart below for minimum distances from roof.
Periodically check that the fl ue is unrestricted.
full length of the chimney. See the Flueing Arrangements chart in the "Flue Arrangement" sec-
tion for minimum and maximum fl ue lengths. See chart below for minimum distances from roof.
Periodically check that the fl ue is unrestricted.
Masonry chimneys may take various contours which the fl exible liner will accommodate. However,
keep the fl exible liner as straight as possible, avoid unnecessary bending.
keep the fl exible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
Required Parts:
Part #
Description
946-529
Co-linear DV Vertical Termination Cap
948-305
3" Flex - 35 ft.
640-994 F37
Dura-Vent
Adapter
946-563
Co-Axial to Co-Linear Adapter Kit
which contains the following:
Co-linear
Flex
Adapter
(270-585)
Outer
Pipe
(946-257)
Inner
Pipe
Adapter
(946-219)
Approved Caps
980 Vertical
980 Vertical
Termination
Cap
923GK 3"
Co-linear
Adapter
with
fl
ashing
INSTALLATION