Lightolier ISF:300 Dépliant

INSTALLATION INSTRUCTIONS FOR 12V LOW VOLTAGE

AND 120V REMODELER

INSTRUCTION SHEET

07-01/Rev-03

ISF:300

A. CEILING:

1. Cut an opening as indicated above. (Fig.1)

Note: Ensure that there is nothing to obstruct the

installation in the ceiling.

B. WIRE-IN:

1. Open junction box cover. (Fig.2)

2. Insert the supply lead into the junction box with a

BX connector (not included).

3. Ground the fixture.

4. Connect the white leads (NEUTRAL) together, and

the black leads (120V) together. (Fig.3, 4 or 5)

5. Close cover. (Fig.2)

Note: Be careful not to pinch leads.

C. HOUSING:

1. Slide the power pack and the housing together into

the ceiling. Snap into place. (Fig.6)

D. RESIDENCE MOUNTING FASTENERS

1. Screw both fasteners screws. (Fig.8)

303MRE MOUNTING FASTENERS:

1. Place (3) holding springs, in the T slots. Slowly

push downward using a short handle screwdriver,

until trim is flush with ceiling, solidify with screws

(3) (included), (Fig.7)

ATTENTION: Insure that the spring is placed

correctly in the T slot, nice and straight then push

down slowly. The spring does not have to be

lowered completely in the slot.

CAUTION: The housing must not be used for

temporary lighting, a protective shield is

required for the lamp.

E. TRIM:

1. Install the trim using the appropriate instruction

sheet.

F. TRANSFORMER / REPLACEMENT:

(Models 301MRE, 303MRE, 401MRE)

Note: Before performing maintenance on the

transformer, make sure that the electrical supply to

the fixture is turned off.

1. Remove the junction box cover and disconnect all

wiring connected to the transformer. (Vig.9)

2. The transformer is held by double sided tape, rotate

with screwdriver under the transformer to loosen it.

(Fig.9)

3. Complete the connections (Fig.5) following the

wiring diagram.

NOTE: WARNING RISK OF FIRE

Transformer contains fixture thermal protector. Use only

replacement transformer obtained from LIGHTOLIER.

DIA* = CEILING CUT-OUT

300MR = 3-3/4" (95mm) Dia*

400MR = 4-3/4" (121mm) Dia*

1" Max. ceiling thickness

300ES = 3-3/4" (95mm) Dia*

1" Max. ceiling thickness

301MRE = 3-3/4" (95mm) Dia*

401MR = 4-3/4" (121mm) Dia*

1" Max. ceiling thickness

303MRE = 3-3/4" (95mm) Dia*

1/2" Max. ceiling thickness

SUPPLY

LEAD

FIG.1

FIG.2

JUNCTION

BOX

CONNECTOR

JUNCTION

B O X

FIG.3

(MR)

INPUT (120V)
NEUTRAL (white)

GROUND

LAMP

LOW VOLTAGE

TRANSFORMER

WHITE

BLACK

THERMAL

PROTECTOR

JUNCTION

B O X

THERMAL

PROTECTOR

LAMP

FIG.4

(ES)

INPUT (120V)

GROUND

NEUTRAL (white)

BLACK

NEUTRAL

WHITE

BLUE

FIG.5

(MRE)

FIG.7

SCREWS

FASTENERS

SCREW

"T"

SLOTS

RETAINING

SPRINGS

HOUSING

FIG.8

CEILING

COVER

FIG.6

POWER PACK

HOUSING

300MR / 400MR

300ES

301MRE - 401MRE

303MRE

JUNCTION BOX

LAMP

LOW VOLTAGE

TRANSFORMER

THERMAL

PROTECTOR

NEUTRAL (white)

GROUND

BLUE

BLACK

INPUT (120V)

NEUTRAL (white)

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with National Electrical Code or Canadian Electrical

Code (as applicable) and local regulations. To ensure full compliance with local codes and regulations, check with your local

electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

FIG.9

SCREWDRIVER

JUNCTION BOX