Lightolier IS:T300 Dépliant

INSTALLATION INSTRUCTIONS FOR MR-16/ES16 TRIM IN PRE-WIRED

INCANDESCENT 12V OR 120V MOUNTING FRAME

Note: For the 50W IC frame-in kit

Put down the lamp shield (included with the IC frame-in kit)

onto the lamp. (Fig.1)

A. LAMP:

1. MR16: Insert the pins of the lamp base into the socket.

(Fig.2)

2. ES16: Insert the pins of the lamp base into the socket.

and rotate the lamp clockwise. (Fig.2A)

3. Turn the lamp under spring (if applicable). (Fig.3,4,5)

CAUTION: Lamp manufacturer recommends that the

protective glass be in place before energizing the

lamp. Insure that the lamp is fully cooled before

relamping.

B. TRIM: Standard (Model 305)

1. Push the trim into the housing. (Fig.6)

2. Aim the lamp beam at the desired angle if necessary.

(Fig.12)

C. TRIM: Adjustable pinhole (Model 308)

1. Push the trim into the housing. (Fig.7)

2. Gently rotate the trim to fit it to the ceiling.

3. Aim the lamp beam at the desired angle if necessary.

(Fig.11)

D. TRIM: Glass (Model 322)

1. Take the loop found at the end of the security cable

attached to the trim and secure by passing the loop

over either one of the screws found within the housing.

(Fig. 8)

2. Push the trim into the housing. (Fig.8)

3. Gently rotate the trim to fit it to the ceiling.

E. TRIM: Adjustable elbow (Model 478)

1. Push the trim into the housing ,compressing the (2)

springs as shown. (Fig.9)

F. TRIM: Wall Washer (Model 315)

1. Push the trim into the housing and position the lamp

shield as shown. (Fig.10)

2. Push the trim into the housing and position the lamp

shield as shown. (Fig.10)

Wall Washer:

1. Position the fixture a minimum of 12 away from the

wall. (Fig.10)

2. Adjust the angle of the beam towards the baffle by

using the frosted glass. (Fig.9)

Accent Lighting:

1. Adjust the angle of the beam to the required position

by using the clear glass.

G. ES16 TRIM: (Models 325, 330)

1. Install the spring tabs into the slots in the base.

(Fig.11)

2. Insert the pins of the lamp base into the socket.

and rotate the lamp clockwise. (Fig.2, 2A)

3. Push the trim into the housing. (Fig.12)

4. Aim the lamp beam at the desired angle if necessary.

(Fig.12)

H. TRIM: Contour (Model 316)

1. For added protection in shower application , install the

gasket for water-tightness (included). Gently fasten

onto the trim. (Fig.13)

I. MAINTENANCE of ALZAK® REFLECTORS OR

ALZAK® CONES: (if applicable)

Note: Handle the reflector or the Alzak® cone with

clean gloves or plastic film to avoid fingerprints.

1. Clean Alzak® surfaces with a clean soft cloth

dampened in a mild detergent solution.

2. Rinse then wipe dry with a dry cloth or a paper towel.

Avoid abrasives.

ATTENTION: Read and understand these instructions before installing fixture. This fixture is intended for installation in accordance with the National

Electrical Code or Canadian Electrical Code (if applicable) and local regulations.To ensure full compliance with local codes and regulations, check with your

local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Retain these instructions for

maintenance reference.

SOCKET

LAMP

FIG.2A

FIG.3

FIG.4

LAMP

SPRING

FIG.5

LAMP

SPRING

PINS

FIG.2

FIG.6

FIG.7

FIG.8

FIG.10

FIG.12

PROTECTIVE

GLASS

TRIM

Model 305

HOUSING

Model 322

Model 315

TRIM

HOUSING

Model 308

SHIELD

WALL

Model 325,330

HOUSING

TRIM

FIG.11

SPRING

TABS

SLOTS

TRIM

HOUSING

FIG.13

LOOP

TRIM

GASKET

LAMP

SECURITY

CABLE

LAMP

SHIELD

FIG.1

INSTRUCTION SHEET

09-01/Rev-03

IST:300

Model 478

HOUSING

SPRINGS

FIG.9