Lightolier LSBW-11 Dépliant
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE
'BMM3JWFS
."t
t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
LSBW-11
1BHFPG
-ZUFTQSFBEÜ-4#1BSBCPMJD8BMM.PVOU-JHIU51FS'PPU /PNJOBM
4FDUJPO
#
Features
1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with
no exposed fasteners or hardware.
2. Lamping: Three T5, 28 or 54 watt (as specified) fluorescent lamps per 4-foot
nominal section. Provided by others.
3. Reflector: Precision die-formed, semi-specular aluminum.
Electrical
Ballast - <10% T.H.D., .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner modules. For special
circuiting, consult factory. Factory installed ballast disconnect allows the ballast
to be disconnected from and reconnected to incoming power under load without
turning the entire circuit off.
coded quick connectors allow ease of connection for joiner modules. For special
circuiting, consult factory. Factory installed ballast disconnect allows the ballast
to be disconnected from and reconnected to incoming power under load without
turning the entire circuit off.
Dimming - 120/277 VAC, 1% dimming level.
Emergency Battery Pack - 28 Watt: 520 Lumens @ 90 min.
54 Watt: 700 Lumens @ 90 min.
Ordering Instructions
Individual Fixtures:
1. Order number of MODULES required.
2. Order one END SET per MODULE.
1. Order number of MODULES required.
2. Order one END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES to complete the run.
3. Order one END SET per run.
1. Determine run length.
2. Order the appropriate number of MODULES to complete the run.
3. Order one END SET per run.
Labels
UL, cUL and I.B.E.W.
Complete ordering instructions below.
Ordering Information
Type
Lamps
Length
Shielding
Ballast
Voltage
Finish
3 = 3-Lamp T5
4 = 4-Foot
C = Parabolic Louver
28 = 28W T5
1 = 120 Volt
AL = Aluminum
8 = 8-Foot
54 = 54W T5
2 = 277 Volt
WH = White
5E = 54W T5 Emergency Pack
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
LSBW
3
C
Mountings
Dual-screw, draw-tight connector to create hairline seam between joiner modules.
Finish
Powder coated baked white or aluminum finish.
Custom colors available, consult factory.
Custom colors available, consult factory.
4. Shielding: Parabolic louver, low-iredescent, semi-specular anodized aluminum
41” (104.14cm) shielding lengthwise, blades are 1-1/3” (3.39cm) high and 2”
(5.08cm) O.C. Louver frame is extruded aluminum and finished to match housing.
(5.08cm) O.C. Louver frame is extruded aluminum and finished to match housing.
4 wire feed required.
11-3/8" (28.89cm)
8-1/2" (21.59cm)
1-3/4"
(4.45cm)
1
2
4
3-1/2" (8.89cm)
3
2-5/8"
(6.67cm)