Lightolier C3AICLV Dépliant
Lightolier
a Genlyte company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2007 Genlyte Group LLC • C1207
We reserve the right to change details of design, materials and finish.
© 2007 Genlyte Group LLC • C1207
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Calculite
®
Evolution IC Airseal
®
Frame-In Kit
C3AICLV
Page 1 of 1
3” Aperture, MR16 (12V)
Features
1. Inner / Outer Housings: Inner Housing - Drawn, 0.036" (20 Ga.) steel. Matte
black finish. Tight rigidly built housing minimizes air leakage to less than
2 CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code and
Washington State Energy Code and reduces heat loss and condensation in
ceiling. Outer Housing - Die-formed, 0.040" aluminum. Top cover removable
for access to transformer. U.L. listed for direct contact with thermal insulation.
2 CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code and
Washington State Energy Code and reduces heat loss and condensation in
ceiling. Outer Housing - Die-formed, 0.040" aluminum. Top cover removable
for access to transformer. U.L. listed for direct contact with thermal insulation.
2. Mounting Frame: Die-formed, 0.036" (20 Ga.) steel, matte black finish. 1/2"
deep integral lip. Four slots are positioned 90° apart to simplify alignment.
3. Trim Kit Horizontal Adjustment Mechanism: Die-formed steel ring, matte
black finish. Provides 362° horizontal stop, lockable with Philips screwdriver.
4. Thick Ceiling Vertical Adjustment Mechanism: Adjustable trim kit verti-
cally to accommodate up to 2" thick ceiling, tool less and lockable.
5. Mounting Bars: Galvanized steel, 0.059" (#16 ga.). Bars pivot for easy
attachment and wire-in below ceiling line. Pre-installed telescoping bars
extend to accommodate 16" to 24" O.C. joist spacing. Bars can accommodate
12" O.C. joist spacing after a slight field modification. Integral nails for
secure attachment to wood; attach to T-bar ceilings with out the need of
accessories.
extend to accommodate 16" to 24" O.C. joist spacing. Bars can accommodate
12" O.C. joist spacing after a slight field modification. Integral nails for
secure attachment to wood; attach to T-bar ceilings with out the need of
accessories.
6. Lamp holder: Procelain bi-pin socket. Pre-wired with No.18 AWG Teflon leads.
7. Junction Box: 3-1/2" X 4" X 2-3/8" deep; 0.063" (#14 ga.) galvanized steel.
7. Junction Box: 3-1/2" X 4" X 2-3/8" deep; 0.063" (#14 ga.) galvanized steel.
UL listed for maximum of (8) No. 12 AWG 90° C through branch circuit con-
ductors. Accessible from inside and outside of luminaire. Outside J-Box door
is hinged for maximum opening.
ductors. Accessible from inside and outside of luminaire. Outside J-Box door
is hinged for maximum opening.
8. Thermal Protector (not shown): Meets NEC and UL requirements.
9. Trim Kit: Order Separately. See individual trim kit specification sheets for
9. Trim Kit: Order Separately. See individual trim kit specification sheets for
information.
Electrical:
Transformer: Replaceable from below; Transformer door rotates into fixture, posi-
tioning transformer directly over aperture to allow one-handed removal Magnetic:
120V 60 Hz., core & coil.
tioning transformer directly over aperture to allow one-handed removal Magnetic:
120V 60 Hz., core & coil.
Note: Magnetic not recommended for residential or
noise sensitive areas. Electronic: 120V 50/60 Hz., regulated lamp voltage, HPF,
EMI and circuit protections, thermal auto-reset, quiet operation.
EMI and circuit protections, thermal auto-reset, quiet operation.
Dimming Controls: Use only dimmers specifically designed for use with
magnetic or electronic transformers. Consult Lightolier Control for information.
Low voltage luminaires may produce audible sound when used with dimmers,
which may be objectionable in acoustically critical areas.
magnetic or electronic transformers. Consult Lightolier Control for information.
Low voltage luminaires may produce audible sound when used with dimmers,
which may be objectionable in acoustically critical areas.
Labels
U.L. (Suitable For Damp Locations), I.B.E.W. U.S. & Foreign Patents pending.
Complies with Air Leakage Requirements as stated in the Model Energy Code
and the Washington State Energy Code.
Complies with Air Leakage Requirements as stated in the Model Energy Code
and the Washington State Energy Code.
Options and Accessories
Plaster Trim Ring (use with flangeless trim kit): CA3FMR
10 1/8"
(257mm)
9" (229mm)
11 3/16"
(284mm)
22 3/8"
(568mm)
14 5/8"
(372mm)
9 1/2"
(242mm)
9" (229mm)
Plus Ceiling Thk.
2" (59mm) Max.
Ceiling Thk.
3" (76mm) Dia.
4" (102mm) Dia.
4
2
9
6 3
5
7
1
8
1
1/2" (13mm) Lip
10 1/8"
(257mm)
9" (229mm)
11 3/16"
(284mm)
(284mm)
22 3/8"
(568mm)
14 5/8"
(372mm)
Ceiling Cutout: 3-1/2” (89 mm) Dia.
For Complete Fixture Order: Trim Kit + Frame-In Kit. Each Sold Separately.
Frame-In-Kit
Lamp
Trim Kit (See individual Trim Kit Specification Sheets)
C3AICLV
Magnetic 120V
20W-50W MR16 (12V)
C3AICLVE1 Electronic 120V
20W-50W MR16 (12V)
Downlight
Wall Washer
Adjustable Accent
Gasslite
Gasslite
Open
1-1/4”
Downlight
Cone
Cone
1-1/4” Downlight Adjustable
Reflector Pinhole
(Wet Loc.)
(Wet Loc.) (Damp Loc) (Wet Loc.) (Wet Loc.)
C3MRD C3MRPD
C3MRL
C3MRA C3MRW C3MRPA C3MRGD C3MRGA
Series Series
Series
Series
Series
Series
Series
Series
Note: Magnetic not recommended for residential or noise sensitive areas.