Lightolier C7CW Dépliant
MULLION
OUTLET BOX SCREWS
MOUNTING PLATE
CANOPY
CANOPY
1/4-20 BOLTS
CLEAT
GASKET
CLEAT
FIG. 4
FIG. 3
FIG. 2
FIG. 1
A
COMPANY
631 Airport Road, Fall River, MA 02720
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:C7CW
Page 1 of 2
A0604
CAUTION:
For wet locations, in accordance with Underwriters Laboratories
requirements, a line of caulking compound such as acrylic or silicone must be
placed around the perimeter of CANOPY to seal water away from the
outlet box and back openings. Use only compatible REFLECTOR TRIMS
rated for use in Wet Locations.
placed around the perimeter of CANOPY to seal water away from the
outlet box and back openings. Use only compatible REFLECTOR TRIMS
rated for use in Wet Locations.
INSTALLATION OF WALL CYLINDER TO OUTLET BOX
(Fig. 1, 2, 3, & 4)
STEP 1:
(Fig. 1, 2, 3, & 4)
STEP 1:
Attach MOUNTING PLATE to outlet box with OUTLET BOX
SCREWS.
STEP 2:
Pass supply leads through opening in CANOPY and CLEAT.
STEP 3:
Attach CANOPY and CLEAT to MOUNTING PLATE with (2) ¼-20
BOLTS (provided).
STEP 4:
Make Connections. Bare Copper and/or green insulation wire(s)
must be connected to SUPPLY GROUND. Connect WHITE BALLAST LEAD
to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to
HOT SUPPLY LEAD. Use wire nuts (local hardware items).
to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to
HOT SUPPLY LEAD. Use wire nuts (local hardware items).
STEP 5:
Install SET SCREWS loosely. Push excess supply leads back into
outlet box. Place cylinder over CLEAT and tighten (2) SET SCREWS.
INSTALLATION OF WALL CYLINDER TO POST OR OTHER
VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)
VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)
1. CLEAT can also be mounted directly to any flat surface such as
MULLION. In this case, use of CANOPY is optional. Bring supply
leads through CLEAT and install CLEAT to wall. For wet locations, in
accordance with Underwriters Laboratories requirements, a line of
caulking compound such as acrylic or silicone must be placed around
the perimeter of EXTRUDED ARM to seal water away from the
wireway and back openings.
MULLION. In this case, use of CANOPY is optional. Bring supply
leads through CLEAT and install CLEAT to wall. For wet locations, in
accordance with Underwriters Laboratories requirements, a line of
caulking compound such as acrylic or silicone must be placed around
the perimeter of EXTRUDED ARM to seal water away from the
wireway and back openings.
2.
Proceed with Step 4 and 5 above.
INSTALLATION OF REFLECTOR TRIM TO CYLINDER (Fig. 4)
Follow installation instructions in Reflector Trim Instruction Sheet.
CAUTION:
DO NOT ENERGIZE THE LAMP UNTIL
REFLECTOR TRIM IS COMPLETELY INSTALLED.
WARNING:
USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’
REFLECTOR TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
INSTALLATION PROCEDURE FOR: C7CW SERIES 7” DIA. H.I.D. WALL CYLINDER
USED WITH C7E17VM, C7E17OVM, C7P38MH, C7E17PL, C7E17FL SERIES FLANGLESS
REFLECTOR TRIM (ORDER SEPARATELY)