Chauvet LEG-6000 Manuale Utente
Operating Instructions
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that
will help you understand its use.
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that
will help you understand its use.
S e t t i n g t h e s t a r t i n g a d d r e s s
1. Press the [MENU] arrow button until the display reads “Addr” .
2. Press the [SELECT] arrow buttons to increase or decrease values until the desired value is
achieved.
3. Press the [MENU] button to activate selection.
User Configurations
{ 1 6 . b r } 8 / 1 6 b i t C o n t r o l C h a n n e l
In the 16 bit Control Channel mode you gain a higher degree of resolution in both Pan and Tilt
movement. One extra channel for both the Pan and the Tilt are added and they perform as the “Fine”
movement.
The primary Pan or Tilt channel is known as the MSB “Most Significant Bit”. This is the channel that
controls the course or broader range of movement. On a DMX signal stream, there are 255 values for
one channel.
The “Fine” Pan or Tilt channel is known as the LSB “Least Significant Bit”. This channel gives you
control of the space between any two MSB values. In other words, it increases the resolution of both
the Pan and Tilt movement, by providing the control of 255 additional values in between each Primary
channel value.
movement. One extra channel for both the Pan and the Tilt are added and they perform as the “Fine”
movement.
The primary Pan or Tilt channel is known as the MSB “Most Significant Bit”. This is the channel that
controls the course or broader range of movement. On a DMX signal stream, there are 255 values for
one channel.
The “Fine” Pan or Tilt channel is known as the LSB “Least Significant Bit”. This channel gives you
control of the space between any two MSB values. In other words, it increases the resolution of both
the Pan and Tilt movement, by providing the control of 255 additional values in between each Primary
channel value.
F
UNCTION
S
ET
T
O
N
OTES
Off
8 bit Control Channel
16.br
On
16 bit Control Channel
{ r . P A n } P a n r e ve r s e / { r . t i l t } T i l t r e ve r s e
It is possible to invert the pan and tilt mirror movement from within the fixture itself. This could be
helpful in situations where the positioning or rigging of a fixture led to a reverse orientation of the
fixture in relation to all or most other fixtures installed. When choosing to command the pan or tilt of
all fixtures at the same time you will notice that the fixtures whose orientation is different from the
others will most likely move opposite of the rest. You can apply a pan and tilt Invert by following the
settings in the table below.
helpful in situations where the positioning or rigging of a fixture led to a reverse orientation of the
fixture in relation to all or most other fixtures installed. When choosing to command the pan or tilt of
all fixtures at the same time you will notice that the fixtures whose orientation is different from the
others will most likely move opposite of the rest. You can apply a pan and tilt Invert by following the
settings in the table below.
F
UNCTION
S
ET
T
O
N
OTES
Off
Left to Right
r.Pan
On
Right to Left
Off
Down to Up
r.tilt
On
Up to Down
{ C H n L } – P a n / T i l t c o n t r o l c h a n n e l r e - a s s i g n
This function will re-position the pan & tilt control channels to start at DMX value number 1.
F
F
UNCTION
S
ET
T
O
N
OTES
Off
Default (Pan/Tilt starts on 10)
CHnL
On
Pan/Tilt re-assign to channel
1-4
1-4
LEG-6000 User Manual
11
Revision: 2007-03-06/09:06