American Standard 2650 Manuale Utente
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
NOTE:
Mounting surface must be clean and level before new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90
Install closet bolts in flange channel,
turn 90
°
, and slide into place 6"
(152 mm) apart and parallel to wall.
SAVE FOR FUTURE USE
3
2
CLOSET FLANGE
CLOSET BOLTS
7 3 0 5 1 3 - 1 0 0 R E V . D
A
FINISHED WALL
FINISHED
FLOOR
FLOOR
SUPPLY
AS
REQ'D.
Saniwares
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 0
© A m e r i c a n S t a n d a r d I n c . 2 0 0 0
!
NOTE:
Pictures may not exactly define contour of china and components.
Ellisse 2184
Heritage 2176
Baby Devoro 2315
Heritage 2176
Baby Devoro 2315
Deco 2059
Cadet III 13L 2650/2660
Sonoma 2454
Cadet III 13L 2650/2660
Sonoma 2454
ROUGHING-IN DIMENSIONS:
NOTE:
NOTE:
Distance from wall to closet flange centerline must
be as listed below:
For 4110 Tanks: A = 10" (254mm)
For 4114 Tanks: A = 14" (356mm)
For all other Tanks: A = 12" (305mm)
For 4114 Tanks: A = 14" (356mm)
For all other Tanks: A = 12" (305mm)
A
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
INSTALLATION
INSTRUCTIONS
For These Two-Piece Toilets:
4
6a
5
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a.
a.
Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
so bolts project through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
marked "THIS SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
WASHER
FLANGE
WAX RING
SEALANT
INSTALL TOILET
Position toilet squarely to wall
and, with a rocking motion, press
bowl down fully on wax ring and
flange. Alternately tighten nuts
until toilet is firmly seated on floor.
and, with a rocking motion, press
bowl down fully on wax ring and
flange. Alternately tighten nuts
until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
!
CLOSET FLANGE