Manualsbrain.com
  1. Manuali
  2. Marche
  3. American Standard
  4. 2171
  5. Manuale Utente

American Standard 2171 Manuale Utente

Scarica
Pagina di 4
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
MONOBLOCK 
LAVATORY FAUCET 
SINGLE LEVER
Installation
Instructions
M 9 6 8 2 9 1 C
Certified to comply with ANSI A112.18.1M
2171
Thank you for selecting American-Standard...the benchmark of fine 
quality for over 100 years.  
To ensure that your installation proceeds smoothly--please read these
instructions carefully before you begin.
by
C O L L E C T I O N
™
T H E
BOSS
GROOVE IN
FAUCET BASE
LAVATORY SINK
OR MOUNTING 
SURFACE
3
2
6
7
1
5
6
1
No sealant is required unless mounting surface is uneven for 3-hole (4" centers)
installation with ESCUTCHEON PLATE (1). Place ESCUTCHEON PLATE (1) over
mounting holes on lavatory sink or mounting surface.
Insert LIFT ROD (7).
From below, install MOUNTING GASKET with
RETAINING WASHER (5) and Nut (6) onto
STUD (4). Pull Faucet to front of sink, so STUD
(4) rests against sink hole. Before final tightening,
align Faucet and ESCUTCHEON (1) so they are
centered on mounting surface. Tighten NUT (6)
to secure Faucet
From below, install MOUNTING GASKET with
RETAINING WASHER (5) and Nut (6) onto
STUD (4). Pull Faucet to front of sink, so STUD
(4) rests against sink hole. Before final tightening,
align Faucet and ESCUTCHEON (1) so they are
centered on mounting surface. Tighten NUT (6)
to secure Faucet
For single hole installation use ESCUTCHEON
RING (2). Install SEAL WASHER (6) into groove
in ESCUTCHEON RING (2) base and place over
over mounting hole in lavatory sink or mounting
surface.
Insert LIFT ROD (7).
Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING
STUD (4) through hole in ESCUTCHEON RING (2).
Seat ESCUTCHEON RING (2) boss into groove in
Faucet base.
Feed FLEXIBLE FAUCET HOSES (3) and MOUNTING STUD (4) through
hole in ESCUTCHEON PLATE (1). Seat ESCUTCHEON PLATE (1) boss
into groove in Faucet base.
INSTALL FAUCET
Turn off water at
main supply.
CAUTION
INSTALLATION OPTIONS; Faucet may be installed with ESCUTCHEON
PLATE (1) or for center hole only with ESCUTCHEON RING (2).
INSTALLATION with ESCUTCHEON PLATE (1)
INSTALLATION with ESCUTCHEON RING (2)
BOSS
GROOVE IN
ESCUTCHEON
RING BASE
Remove as much surface dirt and film using clear 
water and soft cotton cloth (as described above).
Once clean, rinse faucet again with clear water to 
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth. 
To keep your new faucet looking new, please follow
these simple care instructions:
DO:     Simply rinse the faucet clean with clear water.
           Dry the faucet with a soft cotton cloth.
           Do not use any abrasive cleaners, cloths, or 
           paper towels.
           Do not use any cleaning agents containing
           acids, polish abrasives, or harsh cleaners or
           soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
DO NOT:
     Use any of the following to remove tough surface 
     film and build-up:
     Mild liquid detergents
     Clear ammonia free liquid glass cleaners
     Non-acidic, non-abrasive gentle liquid or fully
     dissolved powder cleansers mixed according to
     manufacturers directions.
     Non-abrasive liquid polishers
4