Panasonic SC-HT930 Manuale Utente

37

RQT7972

≥Select “DVD/CD” as the source.
≥Cancel program and random play.

≥Ensure that the unit is connected directly to the television, and is not connected through a video 

cassette recorder.

≥Change “TV Aspect” in the “Video” tab.
≥Use the television to change the aspect. If your television does not have that function, change 

“4:3 Aspect” in Display Menu.

≥Change the Zoom setting.

≥Restore the zoom ratio to “a1.00”.
≥Set “Subtitle Position” in Display Menu to “0”.
≥Set “4:3 Aspect” in Display Menu to “Normal”.

≥Turn off TV’s zoom function.
≥Use the other preset aspect ratios or manual adjustment.
≥Zoom function may not work well, especially in dark scenes and may not work depending on the 

type of disc.

≥Mobile telephone chargers can cause some disturbance.
≥If you are using a TV indoor antenna, change to an outdoor antenna. 
≥The television antenna wire is too close to the unit. Separate the antenna wire of the television 

from the unit.

≥This problem is caused by the editing method or material used on DVD-Video, but should be 

corrected if you use interlace output. Change “Video Output Mode” in Picture Menu to “480i”.

≥Press [PROGRESSIVE] on the main unit so “PRG” is displayed. Or select “480p” in “Video 

Output Mode” in Picture Menu.

≥If the unit is connected to the television through VIDEO OUT or S-VIDEO OUT terminal, output 

will be interlace even if “PRG” is displayed.

≥When progressive output is on, closed captions will not be displayed.

≥Adjust the position of the FM or AM antenna.
≥Use an outdoor antenna.

≥Turn the television off or move it away from the unit.

≥Separate the antenna from other cables.

≥Press [TV] first to operate the television.
≥Check the remote control code for the TV manufacturer.

≥Select “Bright” in “FL Dimmer” in the “Others” tab.

≥You inserted a disc the unit cannot play; insert one it can.
≥You inserted a blank disc.

≥You haven’t inserted a disc; insert one.
≥You haven’t inserted the disc correctly; insert it correctly.

≥Check and correct the speaker cord connections.

If this does not fix the problem, there is a power supply problem. Consult the dealer.

≥Disc is dirty. Wipe it clean.

≥Incorrect operation performed. Read the instructions and try again.

∑∑”

∑∑ stands for a number.

≥Trouble may have occurred. The number following “H” depends on the status of the unit. Turn the 

unit off and then back to ON. Alternatively, turn the unit off, disconnect the AC power supply 
cord, and then reconnect it.

≥If the service numbers fail to clear, note the service number and contact a qualified service person.

[W]” is flashing.

(When using optional SH-FX50)

≥There is no link between the main unit and the receiver. Check that the receiver is turned on.
≥Ensure that the digital transmitter is fully inserted into the slot of the main unit.

“W01” is flashing or lit.
(When using optional SH-FX50)

≥Re-initialize the main unit: While stopped and “DVD/CD” is the source, press and hold [∫] on the 

main unit and [

S10] on the remote control until “Initialized” disappears from the television. Turn 

the unit off and on again. If the problem persists, contact a qualified service person.

/”

≥The operation is prohibited by the unit or disc.

≥You are trying to display incompatible contents.

≥You can only play DVD-Video if their region number is the same or includes the same region 

number as the unit or if the DVD-Video is marked “ALL”. Confirm the region number for the unit 
on the rear panel.

≥Select “On” in “On-Screen Messages” in the “Display” tab.

HT730.book  Page 37  Wednesday, June 1, 2005  8:55 AM