Panasonic SA-BTX70 Manuale Utente

Pagina di 56
23
RQT9479
Listening to the Radio
Up to 30 stations can be set.
Press [RADIO] to select “FM”.
Main unit: Press [RADIO/EXT-IN].
Press [STATUS] to select the position to start the 
auto preset search.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
(FM: 87.9 or 87.5)
CURRENT:
To begin auto preset with the current frequency.*
*
 To change the frequency, refer to “Manual tuning”. (B right)
Press and hold [OK].
Release the button when “AUTO” is 
displayed.
The tuner starts to preset all the stations it 
can receive into the channels in ascending 
order.
≥“SET OK” is displayed when the stations are set, and the radio tunes 
to the last preset station.
≥“ERROR” is displayed when automatic presetting is unsuccessful. 
Preset the stations manually. (
B right)
Press [RADIO] to select “FM”.
Press the numbered buttons to select the 
channel.
To select a 1-digit number
e.g., 1: [1]
> [OK].
To select a 2-digit number
e.g., 12: [1] 
B [2]
Alternatively, press [
X, W] or [2, 1].
When a stereo FM broadcast is being received, 
“ST” lights in the display.
≥The FM setting is also shown on the TV display.
∫ If noise is excessive
When FM is selected
Press [AUDIO] to display “MONO”.
Press the button again to cancel the 
mode.
≥The mode is also canceled when you change the frequency.
≥This setting can be preset for each broadcasting station. When 
“MONO” appears, follow procedures 
1 and 2 in “Presetting stations 
manually”. (
> below)
Press [RADIO] to select “FM”.
Press [SEARCH
6] or [SEARCH5] to select 
the frequency.
≥Main unit:
Press 
[
:
/
6, 5/9] to select the frequency.
≥When a radio broadcast is being 
received, “T” lights in the display.
≥To start automatic tuning, press 
and hold [SEARCH
6] or 
[SEARCH
5] (main unit: [:/6, 5/9]) until the 
frequency starts scrolling. 
Tuning stops when a station is found.
∫ Presetting stations manually
Up to 30 stations can be set.
1 While listening to the radio broadcast
Press [OK].
2 While “P” is flashing on the display
Press the numbered buttons to select a channel.
To select a 1-digit number
e.g., 1: [1]
> [OK].
To select a 2-digit number
e.g., 12: [1] 
B [2]
A station previously stored is overwritten when another station is 
stored in the same channel preset.
FM frequency step
Main unit:
The factory setting is set to 0.2 MHz, it can be changed to receive broadcasts allocated in 0.1 MHz. You may need to change this setting 
if the tuner seems to skip over the correct frequency for stations in your area.
Press [RADIO/EXT-IN] to select “FM”.
Press and hold [RADIO/EXT-IN].
After a few seconds the display changes to show the current lowest frequency. Continue to hold the button down. The lowest frequency changes 
and the step is changed.
To return to the original settings, repeat steps 
1 and 2.
Setting up the radio
Presetting stations automatically
1
@.
2 3
4 5 6
7 8
0
9
OK
EXT-IN
RADIO
STATUS
AUDIO
ABC
DEF
JKL
MNO
TUV
GHI
QRS
P
XYZ
W
_,
SEARCH
SEARCH
RADIO
AUDIO
STATUS
,
SEARCH
SEARCH
OK
Numbered
buttons
Listening/confirming the preset 
channels
Manual tuning
ST
T
MONO
T
MONO
After changing the setting, previously preset frequencies will be cleared. Preset them again.
NOTE
Radio
BTX70PP_eng.book  23 ページ  2009年6月24日 水曜日 午後3時42分