Panasonic SA-BTX70 Manuale Utente

RQT9479

Displays

Page

TV screen and video

The display is dim.

≥Change “FL Display” in the Setup menu.

The elapsed time displayed is
actually less than the play time.

≥The displayed play time is converted from the number of frames at 29.97 frames (equal to

0.999 seconds) to one second. There will be a slight difference between the time displayed
and the actual elapsed time (e.g., actual one-hour elapsed time may display as approximately
59 minutes 56 seconds).

—

The images from this unit do
not appear on the TV.
Picture is distorted.

Jittering occurs.

≥Make sure that the TV is connected to the VIDEO OUT terminal or the HDMI AV OUT

terminal on this unit.

≥Make sure that the TV’s input setting (e.g., VIDEO 1) is correct.

≥If “24p Output” is set to “On” when the unit is connected to a TV through any terminal other

than HDMI, images may not display properly. In this case, set “24p Output” to “Off”.

≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch

to other images, and a black screen is displayed.

≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video. In this case,

turn “24p Output” to “Off”.

≥An incorrect resolution is selected in “HDMI Resolution”, when the TV is connected to HDMI

AV OUT terminals. While stopped, press and hold [

1] and [∫] on the main unit at the same

time for more than 5 seconds to cancel this setting. Set the item again. However, Dolby
Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output the
bitstream, select “Restore Default Settings” to restore the factory presets and make proper
settings.

≥Picture may not be seen when more than 2 devices are connected with HDMI cables.

Reduce the number of connected devices.

≥Mobile telephone chargers can cause some disturbance.

≥If you are using an indoor TV antenna, change to an outdoor antenna.

≥The TV antenna wire is too close to the unit. Move it away from the unit.

—

—
—
—

The screen changes
automatically.

≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return to

the screen saver mode automatically if there is no operation for 5 minutes or more.

Video is not output.

≥An image is not output from the VIDEO OUT terminal when the “High Clarity Sound” is

enabled. Set the “High Clarity Sound” in the on-screen menu to “Off” to use the VIDEO OUT
terminal.

Video is not output in high
definition.

≥High definition video cannot be output through the VIDEO OUT terminal.

≥Confirm that the “HDMI Resolution”, in the Setup menu is set properly.

—

The Setup menu cannot be
accessed.

≥Select “BD/DVD” or “SD” as the source.

Status messages do not appear.

≥Select “Automatic” in “Status Messages” in the Setup menu.

The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.

≥Use the TV to change the aspect. Refer to your TV’s operating instructions.

≥When using an HDMI cable, set “TV Aspect” to “16:9”.

—

When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.

≥Connect this unit to the TV with any cable except the HDMI cable.

There is no apparent change in
picture quality when adjusted
with the “Video” menu in the
on-screen menu.

≥The effect is less perceivable with some types of video.

—

The masked-off area is masked
in gray.

≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is

displayed in black.

Still pictures (JPEG) do not
playback normally.

≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback.

Reference

BTX70PP_eng.book 45 ページ２００９年６月２４日　水曜日　午後３時４２分