ONKYO 29344937 Manuale Utente
48
Notes:
• When the room correction and speaker setup is
• When the room correction and speaker setup is
complete, the Equalizer Settings (page 70) will be set
to “Audyssey” and the “Dynamic EQ” (page 72) will
be set to “On”.
to “Audyssey” and the “Dynamic EQ” (page 72) will
be set to “On”.
• You can cancel the Room Correction and Speaker
Setup at any point in this procedure simply by
disconnecting the setup microphone.
disconnecting the setup microphone.
Error Messages
While the room correction and speaker setup is in
progress, one of the following error messages may
appear:
progress, one of the following error messages may
appear:
❏ Ambient noise is too high
This message appears if there’s too much background
noise and the measurements cannot be performed
properly. Remove the source of the noise and try again.
noise and the measurements cannot be performed
properly. Remove the source of the noise and try again.
❏ Speaker Detect Errors
This message appears if one of the speaker-related errors
below occurs.
• One of the front speakers has not been detected.
• One of the surround speakers has not been detected.
• The surround back speakers have been detected but
below occurs.
• One of the front speakers has not been detected.
• One of the surround speakers has not been detected.
• The surround back speakers have been detected but
the surround speakers haven’t.
• The right surround back speaker has been detected but
the left surround back speaker hasn’t.
❏ Write Error
This message appears if saving fails.
❏ Mismatch Error
This message appears if a speaker that was detected
during the 1st measurement is not detected during the
2nd or 3rd measurements. If this message appears, check
your speaker connections, and then try again.
during the 1st measurement is not detected during the
2nd or 3rd measurements. If this message appears, check
your speaker connections, and then try again.
Changing the Speaker Settings Manually
If you wish to make changes to the settings found during
the automatic speaker setup, follow the directions on
pages 68–70.
the automatic speaker setup, follow the directions on
pages 68–70.
Using a Powered Subwoofer
If you’re using a powered subwoofer, as it outputs very
low-frequency sound and its position is usually low
down, it may not be detected by the Audyssey 2EQ
Room Correction and Speaker Setup. When
“Subwoofer” is set to “No” in the “2-2.Sp Config
(Speaker Configuration)” (page 68), increase the
subwoofer’s volume, select its highest crossover
frequency, and then try running the Audyssey 2EQ
Room Correction and Speaker Setup again. Note that if
the volume is set too high and the sound distorts, it may
not be detected, so use an appropriate volume level.
low-frequency sound and its position is usually low
down, it may not be detected by the Audyssey 2EQ
Room Correction and Speaker Setup. When
“Subwoofer” is set to “No” in the “2-2.Sp Config
(Speaker Configuration)” (page 68), increase the
subwoofer’s volume, select its highest crossover
frequency, and then try running the Audyssey 2EQ
Room Correction and Speaker Setup again. Note that if
the volume is set too high and the sound distorts, it may
not be detected, so use an appropriate volume level.
5
When the following display appears,
move the speaker setup microphone to
measurement point
move the speaker setup microphone to
measurement point
c
then press [ENTER].
Audyssey 2EQ
™
performs more
measurements.
This takes a few minutes.
This takes a few minutes.
When the measurements are complete, the
results are calculated and saved automatically.
results are calculated and saved automatically.
6
When the room correction and speaker
setup is complete, disconnect the
speaker setup microphone.
setup is complete, disconnect the
speaker setup microphone.
To Retry the Room Correction and
Speaker Setup
Speaker Setup
Press the [ENTER] button.
Make sure speakers that cannot be
detected are connected properly.
Make sure speakers that cannot be
detected are connected properly.