Pioneer S-DV180 Manuale Utente
Speaker Setup Guide
01
6
En
Chapter 1
Speaker Setup Guide
Home theater sound setup
Depending on the size and characteristics of
your room, you can place your speakers in one
of two ways using this system. For the speaker
configuration, see the Setup Guide.
your room, you can place your speakers in one
of two ways using this system. For the speaker
configuration, see the Setup Guide.
5 spot/4 spot speaker layout
This is a standard multichannel surround
sound speaker setup for optimal 5.1 channel
home theater sound.
sound speaker setup for optimal 5.1 channel
home theater sound.
3 spot/2 spot speaker layout
This setup is ideal when rear surround speaker
placement isn’t possible or you want to avoid
running long speaker cables in your listening
area.
placement isn’t possible or you want to avoid
running long speaker cables in your listening
area.
Preparing the speakers
Preparation common to all models
Attaching non-skid pads
•
•
Attach the smaller non-skid pads to the
base of each of the speakers. The four large
non-skid pads are for the subwoofer.
U
U
se the supplied adhesive to attach 3 or 4 pads to
the base (flat surface) of each speaker.
Preparation for the HTZ280DVD/
HTZ280DVD-AP/HTZ282DVD/
HTZ282DVD-AP
HTZ280DVD-AP/HTZ282DVD/
HTZ282DVD-AP
The layouts of the 5-spot speaker and 3-spot
speaker are the same:
speaker are the same:
Assembling the speaker stands
•
•
Attach the speaker stand bases to the
stems using the screws provided.
Once you have aligned the stem and base,
secure with the small screws at the points see
the Setup Guide. Note that the speaker should
face in the direction of the base of the isosceles
triangle.
Once you have aligned the stem and base,
secure with the small screws at the points see
the Setup Guide. Note that the speaker should
face in the direction of the base of the isosceles
triangle.
CAUTION
• Be careful not to tighten screws
excessively.
• If excessive force is used to tighten screws,
the threads of screw and/or nut may be
damaged. Use a middle-sized manual
screwdriver during assembly.
damaged. Use a middle-sized manual
screwdriver during assembly.
• Do not use power screwdrivers or oversized
screwdrivers that may exert excessive force
on the screws and nuts.
on the screws and nuts.
• Confirm that no foreign matter is stuck to
the stand base or the tall speaker during
assembly.
assembly.
• If the unit is assembled with foreign matter
stuck between the stand base and the tall
speaker the unit may not be assembled
securely, resulting in tipping or falling.
speaker the unit may not be assembled
securely, resulting in tipping or falling.
• Do not stand on the speaker stand base of
the tall speaker to push or swing the
speaker. The speaker may fall and break, or
someone may be injured. Pay special
attention to children.
speaker. The speaker may fall and break, or
someone may be injured. Pay special
attention to children.
Securing your front and surround
speakers
•
speakers
•
Secure each of the front and surround
speakers using the plastic catch provided.
Screw two supporting hooks into the wall behind
the speaker. Pass a thick cord around the hooks
and through the plastic catch so that the speaker
is stabilized (make sure to test that it supports the
weight of the speaker). After installing, make sure
the speaker is securely fixed.
Screw two supporting hooks into the wall behind
the speaker. Pass a thick cord around the hooks
and through the plastic catch so that the speaker
is stabilized (make sure to test that it supports the
weight of the speaker). After installing, make sure
the speaker is securely fixed.
Plastic catch
Sufficiently thick
cord
cord
HTZ180_181_280_282DVD_En.book 6 ページ ２００９年３月１３日 金曜日 午後２時５０分