Maximatic MX28 IFB Manuale Utente

FILTER BAG

Install filter bag opening around the lip of the opening

on hopper cover.

Secure bag by pulling the bag strap tight.

NOTE:

Optional plastic disposable bags are available and can be

installed in the debris collector bin as easily as installing a plastic bag in
a kitchen garbage bin.

HANDLE

The folding handle has two locked positions; operating and storage posi-
tions.

move handle from either locked position pull out

on both locking

knobs and rotate

turn. Move handle to position needed and return

knobs to the locked position.

BRUSH HEIGHT ADJUSTMENT

WARNING:

DO NOT leave brush running unattended

when machine is in the cleaning mode. Damage to carpet
could occur. To adjust the brush height, press down on knob
and move

the correct setting for the carpet being vacu-

umed. The brush setting is correctwhen the bristles

sweep the

carpet.

HOPPER SWITCH

The vacuum is equipped with a safety switch to prevent the machine from
being switched

on when the hopper cover is open.

OPERATING THE MAXIMATIC VACUUM

The vacuum

designed for use

on large carpeted areas such as airport con-

courses, hotel

room, etc..

Large debris such as paper cups, plates, etc., should be picked up
before starting the cleaning process

Plan your cleaning route to work away from the electrical source

Move machine forward at a steady pace.

- -- -----

POWER

SOURCE

DO NOT

push vacuum over power cord while

machine is running. Always lift cord over vacuum.

WARNING:

Before opening the hopper cover, switch off

machine and wait until fan rotation stops to prevent dust and debris

from being ejected..
3.

To keep the vacuum operating at maximum efficiency: Periodically

switch

off the machine ,shake vacuum bag to allow the finer dirt and dust

to settle into the hopper. Open hopper cover, lift out the dust bin and empty.

CIRCUIT BREAKER

The vacuum is equipped with a circuit breaker to protect the motor in the
event an excessive overload condition occurs. If the breaker trips, wait 2

minutes before resetting. If the breaker trips immediately after resetting,
check for probable cause such as:

A. Brush adjustment set too low
B. Obstructions in brush roller

or impeller.

REGULAR MAINTENANCE

1 .

Shake down bag and empty debris bin daily.
Check power cord for damaged

or frayed insulation.

Return brush adjustment lever to “store” position when the machine
is

not in use.

Every

4 to 6 months remove wheels, clean axles, and apply a thin coat

of silicone lubricant to axles.
The filter bag can be washed twice before losing the filtering cap-

ability. This should be done using a mild detergent

in cool water and

hung up to drip-dry.

3/1/96

SERVICING THE MAXIMATIC

NOTE:

The following service items should

by an autho-

rized service facility or authorized service personnel.

referred

to in these instructions can be identified by using

lists and il-

l trations

the followingpages.

WARNING:

Remove machine power cord from

cal source before making any repairs or adjustments to the ma-
chine.

TO ACCESS IMPELLER

AND MOTOR:

Release hopper cover latches and tilt cover back.
Remove

(5) screws holding main cover to chassis- (2)

located at front corners, (2) located in front of wheels, and (1)
located underneath the machine.

2.
3.

Loosen idler pulley and roll belt off motor pulley.
Remove belt brush pulley guard.
Remove screw from each end of brush shaft and
remove brush assembly.

NOTE: When installing a new belt of motor, center-
line distance between motor shaft and brush shaft
should be

set

at 12

inches.

IMPELLER
DRIVE MOTOR ASSEMBLY

Remove intake duct.

Remove impeller housing cover.

MOTOR

1 .

2.
3.
4.

NOTE:

When re-installing motor use a straight edge to

alignment between brush and motorpulleys.

HOUSING SHOES

NOTE:

When replacing castors or shoes the dimensionsshown

the

illustration below must be made to maintain the

of the vacu-

um.

Loosen (2) screws in impeller and remove from motor shaft.

Loosen idler and roll belt off motor pulley.
Remove intake duct, impeller and housing.
Disconnect motor leads from terminal block.
Remove

(4)

bolts holding motor to chassis.

NOTE:

Make adjustments with the machine in the store position

tingon a LEVEL surfaceand with thecastorspointing toward

The distance between the surface and bottom of the rear brush
housing should be

9/16

inch. Check both right and left side of

housing

When replacing shoes, install a screw in each end of the
shoe first; using a straight edge install balance of
screws keeping the shoe straight.

MAKE ADJUSTM
WITH

CASTERS

POINTING

MUST

POSITION