ICOM S-14217HZ-C1 Manuale Utente
5 - 3
ADJUSTMENT ITEM
ADJUSTMENT CONDITION
VALUE
REFERENCE
FREQUENCY
[Fr]
FREQUENCY
[Fr]
1 •
•
•
•
Connect an RF power meter to the antenna connector.
Loosely couple a frequency counter to the antenna connector.
Transmitting
Loosely couple a frequency counter to the antenna connector.
Transmitting
440.00000 MHz
TX HIGH POWER
(VHF/Low band)
[PH1]
(VHF/Low band)
[PH1]
1 •
•
Connect an RF power meter to the antenna connector.
Transmitting
Transmitting
1.5 W
(VHF/Mid band)
[PH2]
[PH2]
2 • Transmitting
(VHF/High band)
[PH3]
[PH3]
3 • Transmitting
(UHF/Low band)
[PH4]
[PH4]
4 • Transmitting
1.0 W
(UHF/Mid band)
[PH5]
[PH5]
5 • Transmitting
(UHF/High band)
[PH6]
[PH6]
6 • Transmitting
TX LOW POWER
(VHF/Low band)
[PL1]
(VHF/Low band)
[PL1]
1 • Transmitting
0.1 W
(VHF/Mid band)
[PL2]
[PL2]
2 • Transmitting
(VHF/High band)
[PL3]
[PL3]
3 • Transmitting
(UHF/Low band)
[PL4]
[PL4]
4 • Transmitting
(UHF/Mid band)
[PL5]
[PL5]
5 • Transmitting
(UHF/High band)
[PL6]
[PL6]
6 • Transmitting
DEVIATION
(VHF/Low band)
[dE1]
(VHF/Low band)
[dE1]
1 •
•
•
Connect an audio generator to the [MIC/SP] jack through the JIG cable (see
the page 5-1) and set as;
the page 5-1) and set as;
Frequency
: 1.0 kHz
Level
: 90 mVrms (−8 dBm)
Connect a modulation analyzer to the antenna connector through an
attenuator and set as;
attenuator and set as;
LPF
: 20 kHz
HPF
:
OFF
De-emphasis
: OFF
Detector
: (P–P)/2
Transmitting
±4.2 kHz
(VHF/Mid band)
[dE2]
[dE2]
2 • Transmitting
(VHF/High band)
[dE3]
[dE3]
3 • Transmitting
(UHF/Low band)
[dE4]
[dE4]
4 • Transmitting
(UHF/Mid band)
[dE5]
[dE5]
5 • Transmitting
(UHF/High band)
[dE6]
[dE6]
6 • Transmitting
5-2 FREQUENCY AND TRANSMIT ADJUSTMENT
• Set the specifi ed value using [DIAL], and push [BAND] to store the set value. Then push [CALL] to move to the next adjustment item.
NOTE: "REFERENCE FREQUENCY" should be adjusted before "DEVIATION" and "RX SENSITIVITY," and "DEVIATION" should
be adjusted before "DTCS BALANCE" (on the next page).
NOTE: "REFERENCE FREQUENCY" should be adjusted before "DEVIATION" and "RX SENSITIVITY," and "DEVIATION" should
be adjusted before "DTCS BALANCE" (on the next page).
Otherwise, these adjustments will not be adjusted properly.