Yamaha RX-V661 Manuale Utente
55
En
XM Satellite Radio tuning
BA
S
IC
OPERA
T
ION
English
■ All Channel Search mode
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “ALL CH
SEARCH”.
SEARCH”.
2
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to search
for a channel within all channels.
y
• You can search for a channel quickly by pressing and
holding
5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n).
• To display the XM Radio ID number displayed in the front
panel display, select channel “0”.
■ Category Search mode
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “CAT SEARCH”.
2
Press 4
CATEGORY (or DA-E/CAT. l / h)
repeatedly to change the channel category.
3
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to search
for a channel within the selected channel
category.
category.
y
You can search for a channel quickly by pressing and
holding 5PRESET/TUNING/CH l / h on the front
panel (or DPRESET/CH k / n on the remote control).
holding 5PRESET/TUNING/CH l / h on the front
panel (or DPRESET/CH k / n on the remote control).
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting the XM Satellite Radio preset
channels” on page 56.
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting the XM Satellite Radio preset
channels” on page 56.
y
The initial factory setting of all preset channels (A1 to E8) is
“[001] Preview”.
“[001] Preview”.
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “PRESET
SEARCH”.
SEARCH”.
2
Press 4
CATEGORY (or DA-E/CAT. l / h)
repeatedly to change the preset channel
group (A to E).
group (A to E).
3
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to change
the preset channel number (1 to 8).
y
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) (
B
).
■ Direct number access mode
1
Press N
SRCH MODE on the remote control
repeatedly to select “ALL CH SEARCH” or
“CAT SEARCH”.
“CAT SEARCH”.
2
Press the numeric buttons (B) to enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons (B) as shown below.
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons (B) as shown below.
The display changes as follows.
y
• To enter a one-digit or two-digit channel number, press the
numeric buttons (B) on the remote control and then press
MENT to confirm the input number.
MENT to confirm the input number.
• Instead of pressing MENT to tune into the channel
immediately, you can wait a few seconds until this unit
confirms the entered channel number.
confirms the entered channel number.
• If no button is pressed within a few seconds after you enter
a one-digit or two-digit number, this unit automatically
confirms the entered channel number.
confirms the entered channel number.
• Pressing a button other than the numeric buttons (B) or
MENT cancels the Direct Number Access mode
procedure.
procedure.
Before performing operations, set the operation mode selector
on the remote control to
K
SOURCE.
1
CLASSICAL
2
LIVE/CLUB
3
ENTERTAIN
<XM> --1
<XM> -12
<XM>123